Integra DTR-6.2 Connect to devices with z terminals, Connecting power amplifiers

Connections

Connect to devices with z terminals

The z terminal on the DTR-6.2 is for connecting other Integra/ Onkyo components equipped with the same z terminal. When a component are z-connected, you can point the remote controller supplied with the DTR-6.2 at the sensor on the DTR-6.2 and operate that component without having to switch remote controllers.

In addition, by connecting components to the z terminal, you can also perform the system operations given below.

Power on/ready function

When the DTR-6.2 is in the standby state, if an z-connected component is turned on, then the DTR-6.2 also turns on and the input source selected at the DTR-6.2 automatically switches to that component.

If the power cord for an z-connected component is connected to the AC OUTLET on the DTR-6.2, or if the DTR-6.2 is turned on, this function will not work. Also, if you are using the DTR-6.2 for the remote zone (Zone 2), this function will not work.

Direct change function

When the play button is pressed at an z-connected component, the input source selected at the DTR-6.2 automatically changes to that component. However, if you are using the DTR-6.2 for the remote zone (Zone 2), this function will not work.

Power off function

When the DTR-6.2 is placed in the standby state, all z-connected components are also automatically put into the standby state.

CAUTION

If an MD recorder is connected to the TAPE jack on the DTR-6.2, switch the Input Selector from Tape to MD (see page 21).

DTR-6.2

REMOTE

CONTROL

zconnector

Ex: Integra/Onkyo CD player

zconnector

Ex: Integra/Onkyo cassette tape deck

Cautions regarding the AC OUTLETS connectors

The DTR-6.2 is supplied with AC mains outlets for connecting the power cords from other devices so that their power is supplied through the DTR-6.2. By doing this, you can use the Standby/On button on the DTR-6.2 to turn on and off the connected devices as well.

Caution:

Make sure that the total capacity of the other components connected to this unit does not exceed the capacity that is printed on the rear panel (e.g., 120 watts).

AC

OUTLETS

AC 120V 60 Hz

SWITCHED

TOTAL 120W 1 A MAX.

Connecting power amplifiers

Using auxiliary power amplifiers allows you to listen at louder volumes than with the DTR-6.2 alone. If power amplifiers are used, connect each speaker to the corresponding power amplifier.

L (White)		PRE OUT
Front input	FRONT	SURR CENTER
	L	1
R (Red)	R	2
R (Red)
Surround input
L (White)
Center input

	1.	Front left speaker
Power amplifier	2.	Front right speaker
	3.	Surround left speaker
	4.	Surround right speaker
	5.	Center speaker

To connect components using the z terminal, simply connect a remote control cable from this zterminal to the z terminal of the other component. An z remote control cable with a 1/8-inch (3.5-

mm)miniature two-conductor plug comes with every cassette tape deck, compact disc player, MD recorder, and DVD player that has an z terminal.

•For remote control operation, the audio connection cables must also be connected.

•The RC-441M remote controller does not support turntables.

•If a component has two z terminals, you can use either one to connect to the DTR-6.2. The other one can be used to daisy chain with another component.

•With Integra/Onkyo DVD players, you can enter the pre- program code so that you can operate the DVD player directly with the remote controller without connecting the z terminals (see page 50).

1 2 3 4 5

12V TRIGGER A, B terminals

These terminals are provided so that you can use the operation of the DTR-6.2 control the operation of another externally connected device. Connect the component to this 1/8-inch mini-jack terminal and when the set input source is selected, the device will turn on. Set the 12V TRIGGER terminal using the Setup menu: Input setup → 12V trigger (see page 40).

16