Integra DTR-6.2 instruction manual Enjoying music in the remote zone

Enjoying music in the remote zone

ON

Zone 2 indicator Zone 2 Zone 2 Level

Standby/On

Rec Out

Zone 2

Zone 2 Level

CH Level

Master Volume

DSP/ Mode ADJ

Setup

Standby

Return

Power

On Off

Push To Enter

Display

Dimmer

FM Mode

Preset Memory

Tuning

Preset

Smart Scan Navigator

Phones

Audio

Bass

Treble

Selector

DVD

Video 1

Video 2

Video 3

Video 4

Tape

FM

AM

Phono

CD

VCR 1

VCR 2

CH

LEVEL

INPUT

SELECTOR buttons

Input source buttons	Jog dial	ZONE 2
		HOME THEATER CONTROLLER
		RC-441M

Here is an explanation of how to setup speakers in a room separated from the DTR-6.2 so that you can listen to audio sources remotely.

Selecting an input source and adjusting the volume on the DTR-6.2

1. Press the Zone 2 button on the DTR-

Zone 2

6.2.

2. Select a source.

After pressing the Zone 2 button, you must press an input source button within 3 seconds. The Zone 2 indicator lights.

Ex.: When the CD button is pressed. C D

Selecting an input source and adjusting the volume using the remote controller

Turning on the Zone 2 and putting it in the standby state when the DTR-6.2 is in the standby state:

After pressing the ZONE 2 button, press the ON/STDBY button within 5 seconds.

Selecting an input source:

After pressing the ZONE 2 button, press an input source button within 5 seconds.

If tuner is selected with the TUN button, the CH +/- button becomes enabled.

To select the same source for the remote zone that is selected for the main zone, press the Zone 2 button again until “Zone2Sel:SOURCE” appears in the display.

Zone 2

Adjusting the volume:

After pressing the ZONE 2 button, adjust the volume using the LEVEL / buttons within 5 seconds.

Notes:

When “Zone2Sel:Off” is displayed, the output to the remote zone is turned off.

Caution:

If you are not using the system in the remote zone, always press the Zone 2 button consecutively to turn the ZONE 2 function off.

Zone 2 Level

3. Press the Zone 2 Level button.

“Zone2 Level” appears for approximately three seconds.

4. While “Zone 2 Level” is displayed,	DSP/Mode ADJ
turn the jog dial to adjust the volume
to the desired level.
	Push To Enter

Tip:

When using Zone 2, even if you put the DTR-6.2 in the standby state, it will not affect Zone 2 and the volume in Zone 2 can still be adjusted. Moreover, components that have their power supply connect to the AC OUTLET connector on the DTR-6.2 will not be turned off.

•If you wish to use the remote controller from a separate room or other location where the signals will not reach the DTR-6.2, you will need to purchase a commercially available remote control sensor and emitter (see page 20).

•After you press the ZONE 2 button on the remote controller, the Standby indicator on the DTR-6.2 flashes for five seconds. During this time, you will not be able to perform operations in the main zone using the remote controller.

•If the source for the main zone is selected as the source for the remote zone and the source for the main zone is changed, then the source for the remote zone will change as well.

•In the remote zone, you can only play the source in the 2-channel mode. You cannot play the source in the remote zone in the surround mode.

•When you are listening to a source in the remote zone (Zone 2), you can only play sources in the Stereo or Direct modes in the main zone. Therefore, when sources playing from the multichannel input in the main zone, audio from the left and right surround speakers will not be output.

•The Rec Out and Zone 2 buttons use the same circuit and therefore cannot be used at same times. If the Rec Out button is pressed in the main room while someone is using the system in the remote zone, the Zone 2 function will be deactivated and the source will turn off in the remote zone.

•The Zone 2 terminal is an analog output. Digital signals are not output. If no sound is heard from the selected input source, check if the

component is connected to the analog inputs. 45