Installing the Rear I/O Filler Panels | Intel ISP1100 specs

Installing the Rear I/O Filler Panel(s)

CAUTION

Be sure any empty expansion slot(s) have a filler panel installed as described in the following “Installing the Rear I/O Filler Panel(s)” procedure. An open expansion slot reduces the cooling and EMI integrity of the server and can effect performance and/or cause damage due to overheating.

NOTE

Perform this procedure only if you are not immediately reinstalling another add-in card in the same expansion slot from which an add-in card was removed.

Perform this procedure to install rear I/O filler panels in any unused expansion slots. Refer to Figure 23 while performing this procedure.

1.Align the filler panel retention bracket (A) with the two mating screw holes on top of the server back panel.

2.Use a Phillips screwdriver and the two screws (B) removed in the previous “Removing the Filler Panel Retention Bracket” procedure to securely attach the filler panel retention bracket to the top edge of the server back panel.

B

A

C

OMO9461

Figure 23. Installing the Rear I/O Filler Panel(s)

Removing/Installing Server Components

43

Image 43

Intel ISP1100 manual Installing the Rear I/O Filler Panels

Contents

Intel ISP1100 Internet Server Product Guide Disclaimer Contents Configuration Software and Utilities Figures Tables System Components System Components Description Server Board FeaturesServer Board Features Feature Server Board Connectors and Components Server Board Connectors and Components Front Panel Controls, Connectors, and IndicatorsBack Panel Memory ProcessorsSupported Processors Memory Error Detection Mode Supported Memory CharacteristicsDimm Type ECC Disabled ECC Enabled Universal Serial Bus Chipset IDE Support Real-Time Clock, Cmos SRAM, and Battery Serial Ports ControllerDiskette Drive Controller FanMUXCTL0 FanMUXCTL1 Heceta FAN1TACH Input Hardware MonitorKeyboard and Mouse Interface Fan Tachometer MUX Control Mapping Intel Pro/100+ Server 82559 Ethernet Controllers Scsi Hard Drive LED ConnectorWake on LAN Wake on Ring Wake on Ring/Resume on RingResume on Ring SMI and NMI Routing Power ConnectorSMI and NMI Routing Speaker Function Fan Connector DescriptionsConnector Fan Support FCC/Emissions Disclaimer Before You Begin Electrostatic Discharge ESD and ESD Protection Rackmount Precautions Removing the Server From the Rack Safety and Regulatory RequirementsSafety Compliance Tools and Supplies Needed Removing/Installing the Server in the Rack Installing the Server in the Rack Replacing the Cover Removing the Cover Removing the Processor Heat Sink Removing the Processor Removing the Processor Chip Installing the Processor Removing the Processor Fan Removing the Processor Fan If Applicable Installing the Processor Chip Installing the Processor Chip Installing the Processor Heat Sink Installing the Processor Heat Sink Removing the Dimm Boards Removing the Dimm Boards Installing the Dimm Boards Installing the Dimm Boards Removing the Hard Drives Removing the Hard Drives Installing the Hard Drive in the Mounting Bracket Installing the Hard Drives Installing the Hard Drive in the Drive Bay Installing the Hard Drive in the Drive Bay Removing the 3.5-inch Diskette Drive Removing the 3.5-inch Diskette Drive Installing the Drive in the Mounting Bracket Installing the 3.5-inch Diskette Drive Installing the 3.5-inch Diskette Drive in the Drive Bay Installing the 3.5-inch Diskette Drive in the Drive Bay Removing the Filler Panel Retention Bracket Removing the PCI Add-in Cards Removing the Riser and Add-in Cards Removing the Riser and Add-in Cards Removing the Add-in Cards from the Riser Removing the Add-in Cards From the Riser Installing the Rear I/O Filler Panels Installing the Rear I/O Filler Panels Removing the Riser Card Installing PCI Add-in Cards Removing/Installing Server Components Installing the Add-in Cards on the Riser Installing the Add-in Cards on the Riser Removing the Rear I/O Filler Panels Removing the Rear I/O Filler Panels Installing the Riser and Add-in Cards Installing the Riser and Add-in Cards Varning Replacing the Back-up Battery Replacing the Lithium Back-up Battery Power Cord Requirements Power Up the Server Powering Up the Server Removing/Installing Server Components Hot Keys Power-On Self-Test PostConfiguration Utilities Hot Keys Description Using Bios SetupBios Setup Menu Bar Bios Setup Function Keys Advanced Main MenuMain Menu Advanced Menu Advanced Menu Feature OptionsBoot Configuration Submenu Peripheral Configuration Submenu Sectors default Description IDE Configuration MenuIDE Configuration Submenu Options Boot default 44/1.25MB 3.5 default Diskette Configuration SubmenuEvent Log Configuration Submenu Options Auto default Disabled default Security Menu Boot MenuBoot Boot Menu 1st IDE default Last State defaultStay Off default Power On default Stay Off default System Management System Management MenuSystem Management Menu Exit Menu Upgrading the BiosPreparing for the Upgrade Exit Menu Obtaining the Upgrade Utility Recovering the Bios Performing the Upgrade Intel ISP1100 Internet Server Product Guide Configuration Software and Utilities Press Resetting the SystemChecklist Initial System Startup After the System Has Been Running Correctly Running New Application Software Verifying Proper Operation of Key System Lights More Problem Solving ProceduresPreparing the System for Diagnostic Testing Monitoring Post Power Light Does Not Light Specific Problems and Corrective ActionsNo Characters Appear on Screen System Cooling Fans Do Not Rotate Properly Characters Are Distorted or IncorrectDiskette Drive Activity Light Does Not Light CD-ROM Drive Activity Light Does Not Light Hard Disk Drive Activity Light Does Not LightCannot Connect to a Server Problems with Network Problems with Application Software Beeps Error message Bootable CD-ROM Is Not DetectedError and Informational Messages Error Codes and Error Messages Error Messages Description OFF Board Parity Error Addr = Index Post Intel ISP1100 Internet Server Product Guide Index