System Management Menu | Intel ISP1100 specification

System Management Menu

The menu bar is shown below.


Main	Advanced	Security

Boot

System

Management

Exit

Table 22 shows the System Management menu. This menu sets server management features.

Table 22. System Management Menu

Feature

Options

Description

Serial Port

Serial Console Redirection

Baud Rate

Flow Control

LAN Device

LAN Console Redirection

Disabled

COM1 3F8 IRQ4 (default)

COM2 2F8 IRQ3

COM3 3E8 IRQ4

Disabled

Enabled (default)

9600

19.2K (default)

38.4K

115.2K

No Flow Control

CTS/RTS (default)

XON/XOFF

CTS/RTS+CD

Disabled (default)

LAN Device 1

LAN Device 2

Disabled (default)

Enabled

Configures which COM port to use for serial console redirection.

Disables or enables serial console redirection.

Sets the baud rate.

If enabled, it will use the flow control selected. CTS/RTS = Hardware.

XON/XOFF = Software.

CTS/RTS + CD = Hardware + Carrier Detect for modem use.

Configures which LAN device to use for LAN console redirection.

Disables or enables LAN console redirection.

62	Intel ISP1100 Internet Server Product Guide

Image 62

Intel ISP1100 manual System Management Menu

Contents

Intel ISP1100 Internet Server Product Guide Disclaimer Contents Configuration Software and Utilities Figures Tables System Components System Components Feature Server Board FeaturesServer Board Features Description Server Board Connectors and Components Server Board Connectors and Components Back Panel Controls, Connectors, and IndicatorsFront Panel Supported Processors ProcessorsMemory Dimm Type ECC Disabled ECC Enabled Supported Memory CharacteristicsMemory Error Detection Mode Chipset Universal Serial Bus Real-Time Clock, Cmos SRAM, and Battery IDE Support Diskette Drive Controller ControllerSerial Ports Fan Tachometer MUX Control Mapping Hardware MonitorKeyboard and Mouse Interface FanMUXCTL0 FanMUXCTL1 Heceta FAN1TACH Input Wake on LAN Scsi Hard Drive LED ConnectorIntel Pro/100+ Server 82559 Ethernet Controllers Resume on Ring Wake on Ring/Resume on RingWake on Ring Speaker Power ConnectorSMI and NMI Routing SMI and NMI Routing Fan Support Fan Connector DescriptionsConnector Function Before You Begin FCC/Emissions Disclaimer Electrostatic Discharge ESD and ESD Protection Rackmount Precautions Tools and Supplies Needed Safety and Regulatory RequirementsSafety Compliance Removing the Server From the Rack Installing the Server in the Rack Removing/Installing the Server in the Rack Removing the Cover Replacing the Cover Removing the Processor Removing the Processor Heat Sink Installing the Processor Removing the Processor Chip Removing the Processor Fan If Applicable Removing the Processor Fan Installing the Processor Chip Installing the Processor Chip Installing the Processor Heat Sink Installing the Processor Heat Sink Removing the Dimm Boards Removing the Dimm Boards Installing the Dimm Boards Installing the Dimm Boards Removing the Hard Drives Removing the Hard Drives Installing the Hard Drives Installing the Hard Drive in the Mounting Bracket Installing the Hard Drive in the Drive Bay Installing the Hard Drive in the Drive Bay Removing the 3.5-inch Diskette Drive Removing the 3.5-inch Diskette Drive Installing the 3.5-inch Diskette Drive Installing the Drive in the Mounting Bracket Installing the 3.5-inch Diskette Drive in the Drive Bay Installing the 3.5-inch Diskette Drive in the Drive Bay Removing the PCI Add-in Cards Removing the Filler Panel Retention Bracket Removing the Riser and Add-in Cards Removing the Riser and Add-in Cards Removing the Add-in Cards From the Riser Removing the Add-in Cards from the Riser Installing the Rear I/O Filler Panels Installing the Rear I/O Filler Panels Installing PCI Add-in Cards Removing the Riser Card Removing/Installing Server Components Installing the Add-in Cards on the Riser Installing the Add-in Cards on the Riser Removing the Rear I/O Filler Panels Removing the Rear I/O Filler Panels Installing the Riser and Add-in Cards Installing the Riser and Add-in Cards Replacing the Back-up Battery Varning Replacing the Lithium Back-up Battery Power Up the Server Power Cord Requirements Powering Up the Server Removing/Installing Server Components Hot Keys Power-On Self-Test PostConfiguration Utilities Hot Keys Bios Setup Function Keys Using Bios SetupBios Setup Menu Bar Description Main Menu Main MenuAdvanced Peripheral Configuration Submenu Advanced Menu Feature OptionsBoot Configuration Submenu Advanced Menu Options Boot default IDE Configuration MenuIDE Configuration Submenu Sectors default Description Options Auto default Disabled default Diskette Configuration SubmenuEvent Log Configuration Submenu 44/1.25MB 3.5 default Boot Menu Boot MenuBoot Security Menu Power On default Stay Off default Last State defaultStay Off default 1st IDE default System Management Menu System Management MenuSystem Management Exit Menu Upgrading the BiosPreparing for the Upgrade Exit Menu Obtaining the Upgrade Utility Performing the Upgrade Recovering the Bios Intel ISP1100 Internet Server Product Guide Configuration Software and Utilities Initial System Startup Resetting the SystemChecklist Press Running New Application Software After the System Has Been Running Correctly Monitoring Post More Problem Solving ProceduresPreparing the System for Diagnostic Testing Verifying Proper Operation of Key System Lights No Characters Appear on Screen Specific Problems and Corrective ActionsPower Light Does Not Light Diskette Drive Activity Light Does Not Light Characters Are Distorted or IncorrectSystem Cooling Fans Do Not Rotate Properly Cannot Connect to a Server Hard Disk Drive Activity Light Does Not LightCD-ROM Drive Activity Light Does Not Light Problems with Application Software Problems with Network Error Codes and Error Messages Bootable CD-ROM Is Not DetectedError and Informational Messages Beeps Error message Error Messages Description OFF Board Parity Error Addr = Index Post Intel ISP1100 Internet Server Product Guide Index