Intel MPCMM0002 7.0 Rear Connections

MPCMM0002 CMM—Rear Connections

Intel NetStructure® MPCMM0002 Chassis Management Module

Hardware TPS July2007

32 Order Number: 309247-004US

7.0 Rear Connections

7.1 CMM Connector Pinouts

Each CMM has a power connector and a data connector.

7.1.1 CMM Power Connector

The CMM power connectors are standard J12 power receptacles as shown in Figure14.

Figure 14. CMM Power Connector

Contents

Main Page Contents Page Figures Tables Page Revision History 1.0 Document Organization 1.1 Acronyms and Terms The following special acronyms and terms are used in this specification: Table 1. Acronyms and Terms 2.0 Introduction 2.1 Architecture Specification 2.2 User Documentation 2.3 Product Definition Page 3.0 Getting Started 3.1 Installing the CMM 3.1.1 Quick Start 4.0 Module Components 4.1 Block Diagram FPGA 1 FPGA 2 Page 4.2 Intel 80321 Processor Figure 4. Intel 80321 Processor Internal Block Diagram Table 2. Processor Features (Sheet 1 of 2) Table 2. Processor Features (Sheet 2 of 2) 4.3 Memory 4.4 Ethernet 4.5 Serial Port UARTs 4.6 FPGA 4.7 Redundancy and Hot Swap CPLD 4.8 Watchdog Timer 4.9 Real-Time Clock 4.10 ADM1026 Controller 4.11 Hot Swap Controller 4.12 Ride-Through Support 4.13 IPMB Isolation Logic 4.13.1 Dual Star IPMB Isolation CMM 1 CMM 2 Figure 6. Dual Bus IPMB Isolation FPGA 2 5.0 Mechanical Information 5.1 Dimensions Page 5.2 Front Panel Hardware 5.3 Rear Connector Placement 5.3.1 MPCMM0002 CMM Rear Connectors 5.3.2 Coplanar Mating Connectors 5.3.3 Vertical Mating Connectors 5.4 ESD Discharge Strip 6.0 Backplane Considerations 6.1 IPMB Routing 6.2 CMM Power 6.2.1 DC Power Input 6.2.2 CDM Power 6.2.3 Filter Tray CDM 1 CDM 2 6.2.4 Power Switch 6.2.5 Ethernet Routing CMM 1 LAN A LAN B CMM 2 LAN A LAN B Ethernet Fabric A 7.0 Rear Connections 7.1 CMM Connector Pinouts 7.1.1 CMM Power Connector The pinout of each CMM power connector is shown in Tabl e 6. Table 6. Power Connector Pinouts Page Table 10. Power Connector Header Pin Placement Table 9. Power Connector Receptacle Pin Placement (Sheet 2 of 2) 7.1.2 CMM Data Connector The pinouts for the data connector are shown in Tabl e 11. Table 11. Data Connector Pinouts (Sheet 1 of 2) Table 11. Data Connector Pinouts (Sheet 2 of 2) Table 12. Data Connector Pinouts Matrix (Sheet 1 of 3) Table 12. Data Connector Pinouts Matrix (Sheet 2 of 3) Page 7.2 Guide Post 7.3 CMM Redundancy Page 8.0 Chassis Data Modules (CDMs) 8.1 CDM Overview 8.2 CDM LED 8.3 CDM Management 8.4 CDM Power 8.5 CDM Redundancy 9.0 Front Panel 9.1 Serial Port Pinouts Page 9.2 Ethernet Port Pinouts 9.3 Telco Alarm Connector 9.3.1 Cascading the Telco Alarm Connectors Page 9.4 Alarm Quiet Switch CMM 2CMM 1 B C A 9.5 LEDs 9.5.1 Alarm LEDs 9.5.2 Health LED 9.5.3 Hot Swap LED 9.5.4 User-Definable LEDs 10.0 Grounding Considerations 10.1 ESD Discharge Protection 10.2 Chassis Ground and Logic Ground 11.0 Thermals 11.1 Processor Heat Sink 11.2 Module Orientation 11.3 Module Airflow Path Page 11.4 Airflow Requirements 11.5 Board Resistance Curve 11.6 Thermal Sensors 12.0 Management Module Specifications 12.1 Feature Summary 12.2 Dimensions and Weight See Section 5.1, Dimensions on page 24 for more information. 12.3 Environmental Characteristics 12.4 Product Reliability Estimate Table 25. Dimensions and Weight 12.5 Agency Certifications 13.0 Guidelines for Third Party Chassis Vendors 13.1 High Level Design 13.2 IPMB Buses Page Guidelines for Third Party Chassis VendorsMPCMM0002 CMM Figure 34. Radial Bus Topology 13.3 GPIO Pins 13.3.1 Dedicated I/O Pins 13.4 Interfacing FRUs to the CMM 13.4.1 Example Configurations 13.4.1.1 Example Chassis Configuration #1 13.4.1.2 Example Chassis Configuration #2 13.4.1.3 Example Chassis Configuration #3 13.5 Intelligent FRUs 13.6 Non-Intelligent FRUs with I2C* Support 13.6.1 FRUs Based on the ADM1026 13.6.2 Two-Wire Serial Interface Based 13.7 Non-Intelligent FRUs without I2C Support 13.8 FRU Data Storage for Non-Intelligent Devices 13.9 Controllers and I/O Ports for Non-Intelligent Devices 13.10 Temperature Sensors Fronted by the CMM 13.11 Related Documents 14.0 Warranty Information 14.1 Intel NetStructure Compute Boards & Platform Products Limited Warranty 14.2 Returning a Defective Product (RMA) 14.3 For the Americas 14.3.1 For Europe, Middle East, and Africa (EMEA) 14.3.2 For Asia and Pacific (APAC) Page 15.0 Customer Support 15.1 Customer Support 15.2 Technical Support and Return for Service Assistance 15.3 Sales Assistance 15.4 Product Code Summary 16.0 Certifications 16.1 Material Declaration Data Sheet MPCMM0002 CMMCertifications Material Declaration Data Sheet 17.0 Agency Information 17.1 North America (FCC Class A) 17.2 Canada Industry Canada (ICES-003 Class A) (English and French-translated below) 17.3 Safety Instructions (English and French-translated below) 17.3.1 English 17.4 Taiwan Class A Warning Statement 17.3.2 French Page 18.0 Safety Warnings 18.1 Mesures de Scurit Page 18.2 Sicherheitshinweise Page 18.3 Norme di Sicurezza Page 18.4 Instrucciones de Seguridad Page 18.5 Chinese Safety Warning