ADDENDUM TO ISSUE 4 OF THE AXXESS MANUAL OCTOBER 1997
Page 13 of 73
curitycode (if applicable). You hear a confirma-
tion tone followed by DISA dial tone.
If programming from another station, lift the
handset or press the SPKR key.
(2) Enter the Remote Programming feature code
(359). If you have a display, it shows ENTER
EXTENSION. (Executive Keyset users can
pressthe IC DIR key to use the intercom direc-
tory to look up a number.)
(3) Entert he extension to be forwarded. If you have
adi splay, it shows ENTER PASSWORD. Ifyou
entered an invalid extension number,you will
hear reorder tones and can try again.
(4) Enter the extension’spassword, followed by #.
If you have a display, it shows ENTER FEA-
TURE CODE.
NOTE: If youenter an incorrect password, the
display will show INVALID PASSWORD a nd
the call is disconnected. Station users willhear
reorder tones.
(5) To turn on Call Forward:
a. Enter one of the following Call Forward fea-
ture codes. If you enteredan invalid feature
code,you wil l hear reorder tones and can try
again.
Call Forward AllCalls 355............
Call Forward If Busy 357.............
Call Forward If No Answer 356........
Call Forward If No Answer/Busy 358...
b. Enter the forwarding destination. This can
be an extension number or a trunk access
codefollowed by anoutside telephone num-
ber.
If the forward destination is an extension
number, programming is complete and the
call is disconnected automatically.
Ifthe forward destination is an outside num-
ber, hang up to complete the programming.
If the station is not permitted to forwardto
the destination entered, you will hear reor-
der tones and can try again.
If you hang up before entering a forward
destination, the programmed forwardis can-
celed.
(6) To turn off Call Forward: Enter 355 and then
hang up instead of enteringa destination. You
hear a confirmation tone.
Group Listen Feature (Keysets Only)
TheGroup Listen feature allows a keyset user t o trans-
mit a conversation over the keyset speaker while in
handset or headset mode. This allows otherpeople in
the room to listen to the conversation. However, the
keyset microphone remains disabled so that only the
headset or handset usercan speak.
This feature cannot be used on a handsfree call. The
user must be on a call usingthe handset or a headset
before entering the feature code. Group Listen cannot
be used on single-line sets.
TOTURN THE GROUP LISTEN FEATURE ON O ROFF DU RINGA
CALL:
While on a call usingthe handset or a headset,
pressthe Special key and enter the Group Listen
feature code (312). You hear a confirmation
tone and the display shows GROUP LISTEN
ON or GROUP LISTEN OFF. (The other party
will not hear the confirmation tone.)
TheGroup Listen feature code (312) is now included in
the Extensions, Usernames, and Feature Codes pro-
gramming screen. It is also available through the
Executive Keyset displaymenu.
Whenthe feature is active in handset mode, the SPKR
lampwill remain unlit. This allows the userto place the
call intohandsfree mode at any time during the call by
pressing the SPKR key. When the feature is active in
headset mode, the SPKR lamp is lit. Pressing the key
will disconnect the call.
TheGroup Listen feature code can be programmed un-
der a feature key or DSS/BLF key just like any other
feature. The key functions as a toggle. If the key has a
lamp, it is lit when the feature is activated andunlit
when the feature is turned off.
If the Group Listen feature is active when an OHVA
callis received by the keyset,the OHVA call will camp
on (because the speakeris busy).
CO Hookflash on Conference Calls
The system now supports the CO Hookflash feature
code (330) during a conference call.
TO GENERATE A HOOKFLASH WHILE ON A CONFERENCE
CALL:
Press ∞and dial the Hookflash feature
code (330).