Manuals / Invacare / Fitness & Sports / Bicycle

Invacare Top End XLT Pro, Force Removing Road Crown Compensator, Adjusting Road Crown Compensator

Models: Top End XLTTM

1 76

Download 76 pages 35.66 Kb

Page 51

Removing Road Crown Compensator

SECTION 8—SERVICE PROCEDURES

Removing Road Crown Compensator

1.Remove the locknut securing the fork end of the road crown compensator to the fork bolt.

2.Remove the fork end of the road crown compensator from the fork bolt.

3.Remove the bolt and spacer securing the frame end of the road crown compensator to the frame.

Adjusting Road Crown Compensator

NOTE: This adjustment is made for handcycling on crowned roads or in heavy winds.

1.Rotate the fork end of the road crown compensator to adjust the length. Clockwise ‐ shortens the road crown compensator and pulls the front wheel to the left. Counterclockwise ‐ lengthens the road crown compensator and pushes the front wheel to the right.

Adjustment

Road Crown Compensator

Fork End

Installed

Frame

Fork	Road Crown
	Road Crown
	Compensator

Removed

Fork Bolt

Locknut

Frame

Mounting

Hole

Frame

Fork End

Road Crown

Compensator

Frame End

Bolt Spacer

FIGURE 8.3 Installing/Removing/Adjusting the Road Crown Compensator

Part No 1114850

51

Recumbent Handcycle Series

Image 51

Invacare Top End XLT Pro, XLTPRO, XLT Jr, Force Removing Road Crown Compensator, Adjusting Road Crown Compensator, Locknut

Contents

Top End Force Owner’s Operator and Maintenance ManualRecumbent Handcycle Series Top End XLT Top End XLT Jr Top End XLT Pro Top End XLT GoldRecumbent Handcycle Series ACCESSORIES WARNINGSECTION 3-SAFETY INSPECTION TABLE OF CONTENTSTABLE OF CONTENTS SECTION 2-SAFETY AND HANDLINGAdjusting Top End XLT Gold Hand Crank TABLE OF CONTENTSTABLE OF CONTENTS Adjusting Hand Crank Height - All Models Except Top End XLT GoldInstalling/Removing/Adjusting the Steering Dampener TABLE OF CONTENTSTABLE OF CONTENTS SECTION 8-SERVICE PROCEDURESHorizontal Handles/Delrin Handles TABLE OF CONTENTSTABLE OF CONTENTS SECTION 9-OPTIONSREGISTER YOUR PRODUCT Register ONLINE at warranty.invacare.comLIMITED WARRANTY HANDCYCLE TIE-DOWN RESTRAINTS AND SEAT POSITIONING STRAPS DEALER/TECHNICIAN INFORMATIONSPECIAL NOTES HANDCYCLE USERSPECIAL NOTES TOP END XLT JR TYPICAL PRODUCT PARAMETERSTYPICAL PRODUCT PARAMETERS TOP END XLTTOP END XLT PRO TOP END XLT GOLDTYPICAL PRODUCT PARAMETERS SECTION 1-GENERAL GUIDELINES Proper FitOperating Information Care MUST be taken when operating on roads, streets or highways Tire Pressure Weight LimitationA Note to Handcycle Assistants SECTION 2-SAFETY AND HANDLINGSafety and Handling of the Handcycle Stability and BalancePercentage of Weight Distribution Transferring Into/Out of the HandcycleNOTE For this procedure, refer to FIGURE 2.1 on page MUST be secured 6. Shift body weight onto object while transferringIf installed, parking brake Wheel locks MUST be engaged if installedSafety Inspection Checklist SECTION 3-SAFETY INSPECTIONSECTION 3-SAFETY INSPECTION Inspect/Adjust WeeklyInspect/Adjust Monthly Inspect/Adjust PeriodicallySECTION 3-SAFETY INSPECTION Suggested Maintenance Procedures TroubleshootingMaintenance Maintenance Safety Precautions4. Clean/oil quick‐release axles once a week with a Teflon lubricant Initial Setup SECTION 4-INITIAL SETUPTop End XLT/XLT Jr SECTION 4-INITIAL SETUPFIGURE 4.1 Initial Setup NOTE Parking brake located on left side of seat frameBack SECTION 4-INITIAL SETUPFIGURE 4.2 Initial Setup Hand Crank AssemblySECTION 5-OPERATION Riding the HandcycleNOTE For this procedure, refer to FIGURE 5.1 on page Seven Speed Hub Shifting GearsNOTE For this procedure, refer to FIGURE NOTE This procedure applies to the Top End XLT and XLT Jr. ONLYUpper Derailleur Manual Shifter NOTE For this procedure, refer to FIGURE 5.3 on pageHands-On Rapid Fire Shifter/Brake System Twenty-seven Speeds Lower Derailleur Right Side ShifterBacking-Up BrakingReversing Drum Brakes Hand Brakes/Hands-On Brakes Using Parking BrakeNOTE For this procedure, refer to FIGURE NOTE For this procedure, refer to FIGUREHandle UP Steering/CorneringNOTE For this procedure, refer to FIGURE Slots or Hook and Loop Strap Not Shown HandleNOTE This procedure is for Top End XLT, XLT Jr., and XLT Pro ONLY Replacing/Adjusting the Footrest and Leg GuardSECTION 6-RIDING POSITION NOTE For this procedure, refer to FIGURENOTE For this procedure, refer to FIGURE Using/Replacing Footrest StrapUsing Footrest Strap NOTE For this procedure, refer toAdjusting Hand Crank Adjusting Hand Crank Height - All Models Except Top End XLT GoldNOTE For this procedure, refer to FIGURE Adjusting Top End XLT Gold Hand Crank NOTE For this procedure, refer to FIGUREAdjusting Hand Crank Height NOTE For this procedure, refer to FIGURE 1. If installed, activate parking brakeNOTE There is one clamp on the right and left side of the handcycle NOTE For this procedure, refer to FIGURE Adjusting Seat Fore/Aft - XLT Gold and Top End Force OnlyNOTE For this procedure, refer to FIGURE Adjusting Seat Height - All Models Except XLT Gold and Top End ForceAdjusting Back Angle - All Models Except XLT Gold and Top End Force NOTE For this procedure, refer to FIGURENOTE There is one clamp on the right and left side of the handcycle Adjusting Back Angle - XLT Gold NOTE For this procedure, refer to FIGURENOTE Wheel not shown for clarity Adjusting Back Height - Wide Back Option Only NOTE For this procedure, refer to FIGUREPush pin MUST protrude through hole in back cane Installing/Adjusting the Rear Wheel and Quick-Release Axles SECTION 7-WHEELSNOTE For this procedure, refer to FIGURE FIGURE 7.2 Installing the Rear Wheels with Threaded Axles Installing the Rear Wheels with Threaded AxlesReplacing Tire/Tube and Tuning/Replacement of Spokes NOTE For this procedure, refer to FIGURENOTE For optimum accuracy, perform STEP 2 with the handcycle occupied Determining/Adjusting Toe In/Toe OutNOTE For this procedure, refer to FIGURE Determining Toe In/Toe OutReplacing Camber Inserts Adjusting Toe In/Toe OutNOTE For this procedure, refer to FIGURE NOTE Laying the chain flat will prevent kinks in the chain SECTION 8-SERVICE PROCEDURESReplacing the Fork/Crank Assembly NOTE For this procedure, refer to FIGURE 8.1 on page20. Slide the new fork into the frame STEPS 1, 2, 3, 36 SECTION 8-SERVICE PROCEDURESFIGURE 8.1 Replacing the Fork/Crank Assembly AssemblyReplacing the Right Side Crank Arms Replacing the Crank Arms - XLT Gold, XLT PRO and Top End ForceNOTE For this procedure, refer to FIGURE 8.2 on page Replacing the Left Side Crank ArmsInstalling/Removing/Adjusting the Road Crown Compensator Installing Road Crown CompensatorNOTE For this procedure, refer to FIGURE 8.3 on page Compensator Adjusting Road Crown CompensatorRemoving Road Crown Compensator Road CrownRemoving Steering Dampener Installing Steering DampenerAdjusting Steering Dampener NOTE For this procedure, refer to FIGURE 8.4 on pagemounting position on the hand crank assembly Installing Seven Speed Shifter CableNOTE For this procedure, refer to FIGURE NOTE This procedure applies to the Top End XLT onlyNOTE For this procedure, refer to FIGURE 8.6 on page Adjusting/Replacing Seven Speed ShifterInstalling/Adjusting Seven Speed Hub Chain Seven Speed Hub Chain InstallationNOTE For this procedure, refer to FIGURE 8.7 on page Installing/Adjusting Twenty-Seven Speed Cassette ChainAdjusting Seven Speed Hub Chain Installing Twenty-Seven Speed Cassette ChainNOTE For this procedure, refer to FIGURE Adjusting Twenty-Seven Speed Cassette ChainBrake Pads Adjusting/Replacing the Parking BrakeNOTE For this procedure, refer to FIGURE CableReplacing Seat Upholstery NOTE For this procedure, refer toParking Brake Replacing Wide Back Upholstery Replacing Back UpholsteryNOTE For this procedure, refer to NOTE For this procedure, refer toNOTE Rear wheels removed for clarity Installing Rear Safety LightSECTION 9-OPTIONS NOTE For this procedure, refer toNOTE For this procedure, refer to FIGURE Installing the Water BottleInstalling/Using the Tow Bar NOTE For this procedure, refer to FIGURENOTE For this procedure, refer to FIGURE Installing the Draft BumperInstalling the Safety Flag Using Safety HelmetNOTE For this procedure, refer to FIGURE Installing Seat Positioning StrapInstalling the Computer NOTE For this procedure, refer to FIGUREFailure to install handle assembly properly could result in injury Installing Hand Crank HandlesInstalling V/S Crankarm Handles NOTE For this procedure, refer to FIGURE2. Firmly tighten the bolt Failure to install handle assembly properly could result in injuryNOTE For this procedure, refer to FIGURE For Models Made After 7/12/07Mountain Drive Transmission Option Maintenance Installing GlovesMountain Drive Transmission Option Switching to Mountain Drive Transmission OptionNOTE For this procedure, refer to FIGURE 9.14 on page Using the Travel Ready OptionRemoving/Installing the Camber Bar NOTE For this procedure, refer to FIGURE 9.14 on pageInstalling the Fork NOTE For this procedure, refer to FIGURE 9.15 on pageRemoving the Fork Clamps NOTE For this procedure, refer to FIGURE 9.16 on pageRemoving the Front Wheel NOTE For this procedure, refer to FIGURE 9.17 on pageAssembling the Handcycle Rack Assembling/Using/Adjusting the Handcycle RackInstalling the Front Wheel NOTE For this procedure, refer to FIGURE 9.18 on pageUsing the Handcycle Rack Rear Wheel Bar Adjusting the Handcycle RackWheel Tray Bracket Rear Wheel Bar BracketsRear Tires Using the Alignment GaugeNOTE For this procedure, refer to FIGURE Alignment GaugeLIMITED WARRANTY LIMITED WARRANTYThis warranty pertains to the Top End Series Only Canada