Manuals / Invacare / Fitness & Sports / Bicycle

Invacare Top End XLT Pro Initial Setup, NOTE Parking brake located on left side of seat frame

Models: Top End XLTTM

1 76

Page 24

SECTION 4—INITIAL SETUP

	Top End XLT/XLT Jr.
	Seat	Hand Crank Assembly/
Back	Seat	Reversing Drum Brake
Back
		Chain
Rear Wheel		Parking Brake Cable
	Shifter	Footrest
	Location

NOTE: Parking brake located on left side of seat frame.

		Top End XLT PRO
	Back	Hand Crank Assembly	Brake Cable
		Hand Crank Assembly
			Fork Mounted
			Fork Mounted
Rear Wheel			Shifters and Brakes
Rear Wheel

Chain

SeatFootrest

FIGURE 4.1 Initial Setup

Recumbent Handcycle Series

Part No 1114850

Page 24

Image 24

Invacare Top End XLT Pro NOTE Parking brake located on left side of seat frame, 1 Initial Setup, Top End XLT/XLT Jr

Contents

Owner’s Operator and Maintenance Manual Recumbent Handcycle SeriesTop End XLT Top End XLT Jr Top End XLT Pro Top End XLT Gold Top End ForceACCESSORIES WARNING Recumbent Handcycle SeriesTABLE OF CONTENTS TABLE OF CONTENTSSECTION 2-SAFETY AND HANDLING SECTION 3-SAFETY INSPECTIONTABLE OF CONTENTS TABLE OF CONTENTSAdjusting Hand Crank Height - All Models Except Top End XLT Gold Adjusting Top End XLT Gold Hand CrankTABLE OF CONTENTS TABLE OF CONTENTSSECTION 8-SERVICE PROCEDURES Installing/Removing/Adjusting the Steering DampenerTABLE OF CONTENTS TABLE OF CONTENTSSECTION 9-OPTIONS Horizontal Handles/Delrin HandlesREGISTER YOUR PRODUCT Register ONLINE at warranty.invacare.comLIMITED WARRANTY DEALER/TECHNICIAN INFORMATION SPECIAL NOTESHANDCYCLE USER HANDCYCLE TIE-DOWN RESTRAINTS AND SEAT POSITIONING STRAPSSPECIAL NOTES TYPICAL PRODUCT PARAMETERS TYPICAL PRODUCT PARAMETERSTOP END XLT TOP END XLT JRTOP END XLT PRO TOP END XLT GOLDTYPICAL PRODUCT PARAMETERS SECTION 1-GENERAL GUIDELINES Proper FitOperating Information Care MUST be taken when operating on roads, streets or highways Weight Limitation Tire PressureSECTION 2-SAFETY AND HANDLING Safety and Handling of the HandcycleStability and Balance A Note to Handcycle AssistantsPercentage of Weight Distribution Transferring Into/Out of the HandcycleNOTE For this procedure, refer to FIGURE 2.1 on page 6. Shift body weight onto object while transferring If installed, parking brakeWheel locks MUST be engaged if installed MUST be securedSECTION 3-SAFETY INSPECTION Safety Inspection ChecklistInspect/Adjust Weekly SECTION 3-SAFETY INSPECTIONInspect/Adjust Monthly Inspect/Adjust PeriodicallySECTION 3-SAFETY INSPECTION Troubleshooting MaintenanceMaintenance Safety Precautions Suggested Maintenance Procedures4. Clean/oil quick‐release axles once a week with a Teflon lubricant SECTION 4-INITIAL SETUP Initial SetupSECTION 4-INITIAL SETUP FIGURE 4.1 Initial SetupNOTE Parking brake located on left side of seat frame Top End XLT/XLT JrSECTION 4-INITIAL SETUP FIGURE 4.2 Initial SetupHand Crank Assembly BackSECTION 5-OPERATION Riding the HandcycleNOTE For this procedure, refer to FIGURE 5.1 on page Shifting Gears NOTE For this procedure, refer to FIGURENOTE This procedure applies to the Top End XLT and XLT Jr. ONLY Seven Speed HubNOTE For this procedure, refer to FIGURE 5.3 on page Hands-On Rapid Fire Shifter/Brake System Twenty-seven SpeedsLower Derailleur Right Side Shifter Upper Derailleur Manual ShifterBacking-Up BrakingReversing Drum Brakes Using Parking Brake NOTE For this procedure, refer to FIGURENOTE For this procedure, refer to FIGURE Hand Brakes/Hands-On BrakesSteering/Cornering NOTE For this procedure, refer to FIGURESlots or Hook and Loop Strap Not Shown Handle Handle UPReplacing/Adjusting the Footrest and Leg Guard SECTION 6-RIDING POSITIONNOTE For this procedure, refer to FIGURE NOTE This procedure is for Top End XLT, XLT Jr., and XLT Pro ONLYUsing/Replacing Footrest Strap Using Footrest StrapNOTE For this procedure, refer to NOTE For this procedure, refer to FIGUREAdjusting Hand Crank Adjusting Hand Crank Height - All Models Except Top End XLT GoldNOTE For this procedure, refer to FIGURE Adjusting Top End XLT Gold Hand Crank NOTE For this procedure, refer to FIGUREAdjusting Hand Crank Height NOTE For this procedure, refer to FIGURE 1. If installed, activate parking brakeNOTE There is one clamp on the right and left side of the handcycle Adjusting Seat Fore/Aft - XLT Gold and Top End Force Only NOTE For this procedure, refer to FIGUREAdjusting Seat Height - All Models Except XLT Gold and Top End Force NOTE For this procedure, refer to FIGUREAdjusting Back Angle - All Models Except XLT Gold and Top End Force NOTE For this procedure, refer to FIGURENOTE There is one clamp on the right and left side of the handcycle Adjusting Back Angle - XLT Gold NOTE For this procedure, refer to FIGURENOTE Wheel not shown for clarity Adjusting Back Height - Wide Back Option Only NOTE For this procedure, refer to FIGUREPush pin MUST protrude through hole in back cane Installing/Adjusting the Rear Wheel and Quick-Release Axles SECTION 7-WHEELSNOTE For this procedure, refer to FIGURE Installing the Rear Wheels with Threaded Axles Replacing Tire/Tube and Tuning/Replacement of SpokesNOTE For this procedure, refer to FIGURE FIGURE 7.2 Installing the Rear Wheels with Threaded AxlesDetermining/Adjusting Toe In/Toe Out NOTE For this procedure, refer to FIGUREDetermining Toe In/Toe Out NOTE For optimum accuracy, perform STEP 2 with the handcycle occupiedReplacing Camber Inserts Adjusting Toe In/Toe OutNOTE For this procedure, refer to FIGURE SECTION 8-SERVICE PROCEDURES Replacing the Fork/Crank AssemblyNOTE For this procedure, refer to FIGURE 8.1 on page NOTE Laying the chain flat will prevent kinks in the chain20. Slide the new fork into the frame SECTION 8-SERVICE PROCEDURES FIGURE 8.1 Replacing the Fork/Crank AssemblyAssembly STEPS 1, 2, 3, 36Replacing the Crank Arms - XLT Gold, XLT PRO and Top End Force NOTE For this procedure, refer to FIGURE 8.2 on pageReplacing the Left Side Crank Arms Replacing the Right Side Crank ArmsInstalling/Removing/Adjusting the Road Crown Compensator Installing Road Crown CompensatorNOTE For this procedure, refer to FIGURE 8.3 on page Adjusting Road Crown Compensator Removing Road Crown CompensatorRoad Crown CompensatorInstalling Steering Dampener Adjusting Steering DampenerNOTE For this procedure, refer to FIGURE 8.4 on page Removing Steering DampenerInstalling Seven Speed Shifter Cable NOTE For this procedure, refer to FIGURENOTE This procedure applies to the Top End XLT only mounting position on the hand crank assemblyAdjusting/Replacing Seven Speed Shifter Installing/Adjusting Seven Speed Hub ChainSeven Speed Hub Chain Installation NOTE For this procedure, refer to FIGURE 8.6 on pageInstalling/Adjusting Twenty-Seven Speed Cassette Chain Adjusting Seven Speed Hub ChainInstalling Twenty-Seven Speed Cassette Chain NOTE For this procedure, refer to FIGURE 8.7 on pageAdjusting Twenty-Seven Speed Cassette Chain NOTE For this procedure, refer to FIGUREAdjusting/Replacing the Parking Brake NOTE For this procedure, refer to FIGURECable Brake PadsReplacing Seat Upholstery NOTE For this procedure, refer toParking Brake Replacing Back Upholstery NOTE For this procedure, refer toNOTE For this procedure, refer to Replacing Wide Back UpholsteryInstalling Rear Safety Light SECTION 9-OPTIONSNOTE For this procedure, refer to NOTE Rear wheels removed for clarityInstalling the Water Bottle Installing/Using the Tow BarNOTE For this procedure, refer to FIGURE NOTE For this procedure, refer to FIGUREInstalling the Draft Bumper Installing the Safety FlagUsing Safety Helmet NOTE For this procedure, refer to FIGUREInstalling Seat Positioning Strap Installing the ComputerNOTE For this procedure, refer to FIGURE NOTE For this procedure, refer to FIGUREInstalling Hand Crank Handles Installing V/S Crankarm HandlesNOTE For this procedure, refer to FIGURE Failure to install handle assembly properly could result in injuryFailure to install handle assembly properly could result in injury NOTE For this procedure, refer to FIGUREFor Models Made After 7/12/07 2. Firmly tighten the boltInstalling Gloves Mountain Drive Transmission OptionSwitching to Mountain Drive Transmission Option Mountain Drive Transmission Option MaintenanceUsing the Travel Ready Option Removing/Installing the Camber BarNOTE For this procedure, refer to FIGURE 9.14 on page NOTE For this procedure, refer to FIGURE 9.14 on pageInstalling the Fork NOTE For this procedure, refer to FIGURE 9.15 on pageRemoving the Fork NOTE For this procedure, refer to FIGURE 9.16 on page ClampsNOTE For this procedure, refer to FIGURE 9.17 on page Removing the Front WheelAssembling/Using/Adjusting the Handcycle Rack Installing the Front WheelNOTE For this procedure, refer to FIGURE 9.18 on page Assembling the Handcycle RackUsing the Handcycle Rack Adjusting the Handcycle Rack Wheel Tray BracketRear Wheel Bar Brackets Rear Wheel BarUsing the Alignment Gauge NOTE For this procedure, refer to FIGUREAlignment Gauge Rear TiresLIMITED WARRANTY LIMITED WARRANTYThis warranty pertains to the Top End Series Only Canada

Top End XLT/XLT Jr.

NOTE: Parking brake located on left side of seat frame.

Top End XLT PRO

FIGURE 4.1 Initial Setup