Manuals / Invacare / Fitness & Sports / Bicycle

Invacare Top End ForceTM, XLTPRO, Top End XLT Jr, XLT Gold Tire Pressure, Weight Limitation

Models: Top End XLTTM

1 76

Download 76 pages 35.66 Kb

Page 14

Image 14

SECTION 1—GENERAL GUIDELINES

Tire Pressure

DO NOT use your handcycle unless it has the proper tire pressure (p.s.i.). DO NOT overinflate the tires. Failure to follow these suggestions may cause the tire to explode and cause bodily harm.

DO NOT ride on a flat or underinflated tires. Riding on flat or underinflated tires can cause injury, as well as, damage to the tire, tube and handcycle.

Weight Limitation

The Invacare Top End XLT handcycles have a weight limitation of 250 lbs.

A weight limitation label is on the rear axle of the handcycle.

Top View

Weight

Capacity Label

FIGURE 1.1 Weight Limitation

Recumbent Handcycle Series

Part No 1114850

Page 14

Image 14

Invacare Top End ForceTM, XLTPRO, Top End XLT Jr, Top End XLTTM, Top End XLT Pro manual Tire Pressure, Weight Limitation

Contents

Top End XLT Top End XLT Jr Top End XLT Pro Top End XLT Gold Owner’s Operator and Maintenance ManualRecumbent Handcycle Series Top End ForceACCESSORIES WARNING Recumbent Handcycle SeriesSECTION 2-SAFETY AND HANDLING TABLE OF CONTENTSTABLE OF CONTENTS SECTION 3-SAFETY INSPECTIONAdjusting Hand Crank Height - All Models Except Top End XLT Gold TABLE OF CONTENTSTABLE OF CONTENTS Adjusting Top End XLT Gold Hand CrankSECTION 8-SERVICE PROCEDURES TABLE OF CONTENTSTABLE OF CONTENTS Installing/Removing/Adjusting the Steering DampenerSECTION 9-OPTIONS TABLE OF CONTENTSTABLE OF CONTENTS Horizontal Handles/Delrin HandlesLIMITED WARRANTY REGISTER YOUR PRODUCTRegister ONLINE at warranty.invacare.com HANDCYCLE USER DEALER/TECHNICIAN INFORMATIONSPECIAL NOTES HANDCYCLE TIE-DOWN RESTRAINTS AND SEAT POSITIONING STRAPSSPECIAL NOTES TOP END XLT TYPICAL PRODUCT PARAMETERSTYPICAL PRODUCT PARAMETERS TOP END XLT JRTYPICAL PRODUCT PARAMETERS TOP END XLT PROTOP END XLT GOLD Operating Information SECTION 1-GENERAL GUIDELINESProper Fit Care MUST be taken when operating on roads, streets or highways Weight Limitation Tire PressureStability and Balance SECTION 2-SAFETY AND HANDLINGSafety and Handling of the Handcycle A Note to Handcycle AssistantsNOTE For this procedure, refer to FIGURE 2.1 on page Percentage of Weight DistributionTransferring Into/Out of the Handcycle Wheel locks MUST be engaged if installed 6. Shift body weight onto object while transferringIf installed, parking brake MUST be securedSECTION 3-SAFETY INSPECTION Safety Inspection ChecklistInspect/Adjust Weekly SECTION 3-SAFETY INSPECTIONSECTION 3-SAFETY INSPECTION Inspect/Adjust MonthlyInspect/Adjust Periodically Maintenance Safety Precautions TroubleshootingMaintenance Suggested Maintenance Procedures4. Clean/oil quick‐release axles once a week with a Teflon lubricant SECTION 4-INITIAL SETUP Initial SetupNOTE Parking brake located on left side of seat frame SECTION 4-INITIAL SETUPFIGURE 4.1 Initial Setup Top End XLT/XLT JrHand Crank Assembly SECTION 4-INITIAL SETUPFIGURE 4.2 Initial Setup BackNOTE For this procedure, refer to FIGURE 5.1 on page SECTION 5-OPERATIONRiding the Handcycle NOTE This procedure applies to the Top End XLT and XLT Jr. ONLY Shifting GearsNOTE For this procedure, refer to FIGURE Seven Speed HubLower Derailleur Right Side Shifter NOTE For this procedure, refer to FIGURE 5.3 on pageHands-On Rapid Fire Shifter/Brake System Twenty-seven Speeds Upper Derailleur Manual ShifterReversing Drum Brakes Backing-UpBraking NOTE For this procedure, refer to FIGURE Using Parking BrakeNOTE For this procedure, refer to FIGURE Hand Brakes/Hands-On BrakesSlots or Hook and Loop Strap Not Shown Handle Steering/CorneringNOTE For this procedure, refer to FIGURE Handle UPNOTE For this procedure, refer to FIGURE Replacing/Adjusting the Footrest and Leg GuardSECTION 6-RIDING POSITION NOTE This procedure is for Top End XLT, XLT Jr., and XLT Pro ONLYNOTE For this procedure, refer to Using/Replacing Footrest StrapUsing Footrest Strap NOTE For this procedure, refer to FIGURENOTE For this procedure, refer to FIGURE Adjusting Hand CrankAdjusting Hand Crank Height - All Models Except Top End XLT Gold Adjusting Hand Crank Height Adjusting Top End XLT Gold Hand CrankNOTE For this procedure, refer to FIGURE NOTE There is one clamp on the right and left side of the handcycle NOTE For this procedure, refer to FIGURE1. If installed, activate parking brake Adjusting Seat Fore/Aft - XLT Gold and Top End Force Only NOTE For this procedure, refer to FIGUREAdjusting Seat Height - All Models Except XLT Gold and Top End Force NOTE For this procedure, refer to FIGURENOTE There is one clamp on the right and left side of the handcycle Adjusting Back Angle - All Models Except XLT Gold and Top End ForceNOTE For this procedure, refer to FIGURE NOTE Wheel not shown for clarity Adjusting Back Angle - XLT GoldNOTE For this procedure, refer to FIGURE Push pin MUST protrude through hole in back cane Adjusting Back Height - Wide Back Option OnlyNOTE For this procedure, refer to FIGURE NOTE For this procedure, refer to FIGURE Installing/Adjusting the Rear Wheel and Quick-Release AxlesSECTION 7-WHEELS NOTE For this procedure, refer to FIGURE Installing the Rear Wheels with Threaded AxlesReplacing Tire/Tube and Tuning/Replacement of Spokes FIGURE 7.2 Installing the Rear Wheels with Threaded AxlesDetermining Toe In/Toe Out Determining/Adjusting Toe In/Toe OutNOTE For this procedure, refer to FIGURE NOTE For optimum accuracy, perform STEP 2 with the handcycle occupiedNOTE For this procedure, refer to FIGURE Replacing Camber InsertsAdjusting Toe In/Toe Out NOTE For this procedure, refer to FIGURE 8.1 on page SECTION 8-SERVICE PROCEDURESReplacing the Fork/Crank Assembly NOTE Laying the chain flat will prevent kinks in the chain20. Slide the new fork into the frame Assembly SECTION 8-SERVICE PROCEDURESFIGURE 8.1 Replacing the Fork/Crank Assembly STEPS 1, 2, 3, 36Replacing the Left Side Crank Arms Replacing the Crank Arms - XLT Gold, XLT PRO and Top End ForceNOTE For this procedure, refer to FIGURE 8.2 on page Replacing the Right Side Crank ArmsNOTE For this procedure, refer to FIGURE 8.3 on page Installing/Removing/Adjusting the Road Crown CompensatorInstalling Road Crown Compensator Road Crown Adjusting Road Crown CompensatorRemoving Road Crown Compensator CompensatorNOTE For this procedure, refer to FIGURE 8.4 on page Installing Steering DampenerAdjusting Steering Dampener Removing Steering DampenerNOTE This procedure applies to the Top End XLT only Installing Seven Speed Shifter CableNOTE For this procedure, refer to FIGURE mounting position on the hand crank assemblySeven Speed Hub Chain Installation Adjusting/Replacing Seven Speed ShifterInstalling/Adjusting Seven Speed Hub Chain NOTE For this procedure, refer to FIGURE 8.6 on pageInstalling Twenty-Seven Speed Cassette Chain Installing/Adjusting Twenty-Seven Speed Cassette ChainAdjusting Seven Speed Hub Chain NOTE For this procedure, refer to FIGURE 8.7 on pageAdjusting Twenty-Seven Speed Cassette Chain NOTE For this procedure, refer to FIGURECable Adjusting/Replacing the Parking BrakeNOTE For this procedure, refer to FIGURE Brake PadsParking Brake Replacing Seat UpholsteryNOTE For this procedure, refer to NOTE For this procedure, refer to Replacing Back UpholsteryNOTE For this procedure, refer to Replacing Wide Back UpholsteryNOTE For this procedure, refer to Installing Rear Safety LightSECTION 9-OPTIONS NOTE Rear wheels removed for clarityNOTE For this procedure, refer to FIGURE Installing the Water BottleInstalling/Using the Tow Bar NOTE For this procedure, refer to FIGUREUsing Safety Helmet Installing the Draft BumperInstalling the Safety Flag NOTE For this procedure, refer to FIGURENOTE For this procedure, refer to FIGURE Installing Seat Positioning StrapInstalling the Computer NOTE For this procedure, refer to FIGURENOTE For this procedure, refer to FIGURE Installing Hand Crank HandlesInstalling V/S Crankarm Handles Failure to install handle assembly properly could result in injuryFor Models Made After 7/12/07 Failure to install handle assembly properly could result in injuryNOTE For this procedure, refer to FIGURE 2. Firmly tighten the boltSwitching to Mountain Drive Transmission Option Installing GlovesMountain Drive Transmission Option Mountain Drive Transmission Option MaintenanceNOTE For this procedure, refer to FIGURE 9.14 on page Using the Travel Ready OptionRemoving/Installing the Camber Bar NOTE For this procedure, refer to FIGURE 9.14 on pageRemoving the Fork Installing the ForkNOTE For this procedure, refer to FIGURE 9.15 on page NOTE For this procedure, refer to FIGURE 9.16 on page ClampsNOTE For this procedure, refer to FIGURE 9.17 on page Removing the Front WheelNOTE For this procedure, refer to FIGURE 9.18 on page Assembling/Using/Adjusting the Handcycle RackInstalling the Front Wheel Assembling the Handcycle RackUsing the Handcycle Rack Rear Wheel Bar Brackets Adjusting the Handcycle RackWheel Tray Bracket Rear Wheel BarAlignment Gauge Using the Alignment GaugeNOTE For this procedure, refer to FIGURE Rear TiresThis warranty pertains to the Top End Series Only LIMITED WARRANTYLIMITED WARRANTY Canada