JVC RX-DP10VBK Changing the Display Brightness, Press DIMMER, Making Sounds Natural, Press TV/DBS

Changing the Display Brightness

You can dim the display.

Press DIMMER.

•Each time you press the button, the brightness level of the display changes as follows:

DIMMER DIMMER

Making Sounds Natural

JVC’s CC (Compensative Compression) Converter eliminates jitter and ripples, achieving a drastic reduction in digital distortion by processing the digital music data in 24 bit–quantization and by expanding the sampling frequency to 176.4 kHz (for fs 44.1 kHz signals)/192 kHz (for fs 48 kHz signals).

By using the CC Converter, you can obtain a natural sound field from any source.

On the unit On the remote control

Dimmer Much dimmer

Canceled (Normal display)

Note:

Even though the dimmer is in use, the display brightens for a while when you operate the receiver (except when changing the source).

Turning Line Direct On and Off

You can enjoy the sound closer to original source by skipping the sound adjustments such as Midnight mode (see page 38), speaker output level adjustments (see page 44) and Parametric Equalizer (see page 44). You can only adjust the volume level while Line Direct is in use.

• You have to make this setting for each source.

Press LINE DIRECT.

•Each time you press the button, Line Direct turns on and off.

–When Line Direct turns on, “LINE DIRECT” appears in the main display.

Press CC CONVERTER so that the CC

CONVERTER lamp lights up.

•Each time you press the button, CC Converter turns on and off (the lamp goes off) alternately.

CC CONVERTER CC CONVERTER

On the unit On the remote control

Note:

•This function is applied only to the main room sources.

•You cannot use this function while Line Direct or THX Surround is in use. If you turn on Line Direct or THX Surround while this function is in use, this function will be canceled.

Changing the Source Name

When you have connected an MD recorder to the TAPE/MD jacks or the DBS tuner to the TV SOUND/DBS jacks on the rear panel, change the source name which will be shown on the display when you select the MD recorder or DBS tuner as the source.

On the unit ONLY:

LINE DIRECT

LINE DIRECT

When changing the source name from “TAPE” to “MD”:

1. Press TAPE/MD.

TAPE/MD

On the unit

On the remote control

2. Press and hold TAPE/MD until

(inside the front door)

ANALOG		SPEAKERS	1
L	R
SUBWFR			VOLUME

dB

Ex. When the source is “VIDEO.”

Notes:

“ASSGN. MD” appears on the display.

ANALOG		SPEAKERS	1
L	R
SUBWFR			VOLUME

dB

When changing the source name from “TV ” to

•This function is applied only to the main room sources.

•If you turn on Line Direct while using the Surround and DSP modes, the effect changes as follows:

“DBS”:

1. Press TV/DBS.

TV/DBS

Input	Mode	Surround	DSP
Analog		Not valid	Not valid
Digital		Valid	Not valid

•If you turn on Line Direct, CC Converter (see the right column) is canceled.

•Turning off Line Direct activates the sound adjustments previously selected such as Midnight mode, speaker output level adjustments and Parametric Equalizer.

•If you turn off Line Direct while listening to an analog source, muting time* will be a little longer. (* The period during which no sound comes out.)

2. Press and hold TV/DBS until “ASSGN. DBS” appears on the display.

ANALOG		SPEAKERS	1
L	R
SUBWFR			VOLUME

dB

To change the source name to “TAPE” or “TV,” repeat the same procedure above — press and hold TAPE/MD to select “TAPE,” or press and hold TV/DBS to select “TV” in step 2.

•While selecting “DBS” as the sub-room source, you cannot change the source name to “TV.”

25