Getting Started, Before Installation, General | JVC RX-DP10VBK

Getting Started

Getting Started

This section explains how to connect audio/video components and speakers to the receiver, and how to connect the power supply.

Before Installation

General

Connecting the FM and AM Antennas

FM Antenna Connections

•Be sure your hands are dry.

•Turn the power off on all components.

•Read the manuals supplied with the components you are going to connect.

Location

•Install the receiver in a location that is level, well-ventilated and free from moisture.

•The temperature around the receiver must be between –5˚C and 35˚C (23˚F and 95˚F).

•Make sure there is good ventilation around the receiver. Poor ventilation could overheat and damage the receiver.

Handling the receiver

ANTENNA

AM

EXT

AM

LOOP

FM 75

COAXIAL

Extend the supplied FM antenna horizontally.

FM Antenna

Outdoor FM Antenna Cable (not supplied)

•Do not insert any metal object into the receiver.

•Do not disassemble the receiver or remove screws, covers, or cabinet.

•Do not expose the receiver to rain or moisture.

Checking the Supplied Accessories

Check to be sure you have all of the following items, which are supplied for the receiver.

The number in the parentheses indicates quantity of the pieces supplied.

•Remote Control (1)

•Batteries (2)

•AM Loop Antenna (1)

•FM Antenna (1)

•RF Rod Antenna (1)

•IR Signal Transmitter (1)

•Double-Sided Adhesive Tape (1)

•Front Terminal Cover (1)

A	ANTENNA		B	ANTENNA
A	AM		B	AM
	EXT			EXT
	AM			AM
	LOOP			LOOP
	75	L		75	L
	FMAXIA			FMAXIA
	CO			CO
			AM
			LOOP

A. Using the Supplied FM Antenna

The FM antenna provided can be connected to the FM 75Ω COAXIAL terminal as a temporary measure.

B. Using the Standard Type Connector with Outdoor FM Antenna (not Supplied)

A standard type connector should be connected to the FM 75Ω COAXIAL terminal.

Note:

If reception is poor, connect the outdoor antenna.

Before attaching a 75Ω coaxial cable (the kind with a round wire going to an outdoor antenna), disconnect the supplied FM antenna.

If any item is missing, contact your dealer immediately.

6

Image 9

JVC RX-DP10VBK Getting Started, Before Installation, Connecting the FM and AM Antennas, Checking the Supplied Accessories

Contents

AUDIO/VIDEO CONTROL RECEIVER RX-DP10VBKINSTRUCTIONS LVT0722-003A Caution––SPEAKERLOAD SELECTOR switch Caution ––STANDBY/ON switchWarnings, Cautions and Others WARNING: TO REDUCE THE RISK OF FIRE For the remote control Note to CATV system installerFor the main unit Basic Settings Table of ContentsSound Adjustments Using the Surround Modes Precautions FeaturesIntroduction RF/IR multi-brand/learningremote control Parts Identification Display Window Front PanelRefer to the pages in parentheses for details 1SPEAKERS 1 button 18, 12 3 Connecting the FM and AM Antennas Before InstallationChecking the Supplied Accessories Getting Started AM Antenna Connections Connecting the SpeakersNotes Main room speaker layout 2Turn the knob counterclockwise 3Insert the speaker signal cable4Turn the knob clockwise Basic connecting procedure Power amplifier Power amplifier Power amplifierConnecting Audio/Video Components Power amplifier CD recorder CD playerCassette deck or MD recorder R DVD L Video component connections VCRsVideo camera TV and/or DBS tuner DBS tunerNotes DVD player Digital Connections Digital input terminalsDigital output terminal Setting Up the IR Signal Transmitter Setting Up the RF Rod Antenna1. Find the place where you attach the IR signal to the IR signal transmitter Connecting the Power Cord Putting Batteries in the Remote Control2.Insert the batteries 3.Replace the cover Required Connections for Sub-Room Multi-RoomOperationsPower amplifier Sub-roomLayout 1. Press STANDBY/ON Basic Operating Procedure for Main Room1. Set MAIN ROOM/SUB ROOM LEARN/TRANSMIT selector to 6. Turn MASTER VOLUME to Basic Operating Procedure for Sub-Roomadjust the volume level of the 4. Press VOLUME +/– to adjust the Main Room Operations Turning the Power On and Off StandbyFrom the remote control To turn on the power, press Selecting the Main Room Source to Play Canceling the Main Room OperationsSUBWFR Speaker and signal indicators on the display SUBWFR LFE Adjusting the Main Room Volume1. Press SOUND SELECTOR inside as the VCR or DVD player, etc Selecting the Analog or Digital Input Mode Activating the Main Room Front Speakers headphones connected Attenuating the Input SignalPress and hold INPUT MODE/INPUT INPUT MODE Muting the Main Room Sound Press DIMMER Changing the Display BrightnessMaking Sounds Natural Turning Line Direct On and Off Press SLEEP repeatedly Using the Sleep TimerBasic adjustment auto memory From the remote control ONLY and Selecting the Sub-RoomOperations Sub-RoomOperations2. Press SUB ROOM ON/OFF so that the SUB ROOM ON/OFF lamp lights “SUB ROOM.” Canceling the Sub-RoomOperationsFrom the remote control From the remote control Selecting the Sub-RoomSource to Play Adjusting the Sub-RoomVolumeFrom the remote control On the unit Press SPEAKERS 2/SUB ROOM to Activating the Sub-RoomFront Speakersactivate the sub-roomfront speakers Muting the Sub-RoomSound 2.Press TUNING UP or TUNING Tuning into Stations ManuallyReceiving Radio Broadcasts 1. Press FM or AM 2. Press SET inside the front door Using Preset Tuning3. Press RIGHT or LEFT inside the front door to select a Setup Menu Configuration Basic Settings From the remote control Operation through On-ScreenDisplay MenusMenu operation buttons For the main room operations 1. Press SETUP MENU Menu Operating Procedure3. Press SET repeatedly to select an item Setting the Speaker Distance —SPEAKERDISTANCE Setting the Speakers —SPEAKERSETTINGLSB RSB 7For subwoofer 7Setting the crossover frequency Setting the Bass Sounds—SUBWOOFER37Setting the low frequency effect attenuator LFE 7Changing the sound phase Setting the Digital Input Terminals -DIGITALIN Setting the Dynamic Range —DYNAMICRANGE7Setting the Midnight mode 7Setting THX Surround EX When “COAXIAL INPUT” is set to “DVD” Turning On and Off the Video Output —VIDEOPOWERWhen “COAXIAL INPUT” is set to “CD” When “COAXIAL INPUT” is set to “TV” or “DBS” Preparing for the Sub-RoomOperations —SUBROOM p Adjustment Menu Configuration Sound Adjustments Operation through On-ScreenDisplay Menus From the remote controlMenu operation buttons For the main room operations Menu Operating Procedure 1. Press ADJUST MENU3. Press SET repeatedly to select an item 7Adjusting the speaker channel output levels Adjusting the Parametric Equalizer —PARAMETRICEQ7Adjustment procedure on this submenu Notes Adjusting the Center Channel —CENTERCHANNEL Adjusting the DSP Parameters —DSPPARAMETER7 Adjustment procedure on this submenu 7Adjustment screen Reproducing Theater Ambience Using the Surround ModesIntroducing the Surround Modes THX Surround EX Dolby Digital EX Input Signals Surround modes available for input signalsDolby Surround Dolby Pro Logic DTS Digital Surround 1.Select and play any sound source Activating the Surround Modes 1. Press SOUND Adjusting the Surround Sounds Temporarily2. Press TEST once to check the speaker output balance Reproducing the Sound Field Using the DSP ModesIntroducing the DSP Modes DAP modes 2.Press DSP MODE repeatedly until the DSP mode Activating the DSP Modesyou want appears on the display 1.Select and play any sound source 2. Press EFFECT to adjust the overall Adjusting the DSP Parameters Temporarily3. Press ROOM SIZE to adjust the room 4. Press LIVENESS to adjust the Activating the DVD MULTI Playback Mode Using the DVD MULTI Playback Mode Notes COMPU LINK Remote Control SystemAutomatic Source Selection For the main room operations 3. Press the play 3 button on the CD player the same time TEXT COMPU LINK Remote Control System CONNECTIONSFUNCTIONS Disc Information screen OPERATIONSTo exit from the Disc information screen Note on 3. Press %/ Þto move to “PERFORMER,” 2. Press %/ Þto move to “SEARCH,” then press SETthen press SET 4. Press %/ Þ/ @/ #to 2. Press %/ Þto move 3.Press %/ Þto move to “GENRE,” then press SETto “TITLE INPUT,” then press SET 2. Press %/ Þto move to “SEARCH,” then press SET 5.Press %/ Þ/ @/ #to move to “DISC 32 charactersMICHAEL in this example,” then press SET 7. Press %/ Þ/ @/ #to move to “DISC AV COMPU LINK Remote Control System CONNECTIONS 1: IR Signal Transmitter ConnectionCONNECTIONS 2: AV COMPU LINK Connection One-TouchVideo Play CONNECTIONS 3: Video Cable Connection Automatic Power On Automatic Power On/Off StandbyOne-TouchDVD Play Notes Operating Audio Components Operating JVC’s Audio/Video ComponentsTuner Sound control section Amplifier CD player-changer CD playerTurntable CD recorder Operating Video Components VCR VCR connected to the VCR 1 jacksDVD player Operating Other Manufacturers’ Equipment Changing the Preset Signal Codes1.Set the TV operation mode selector to “TV.” 2.Press and hold TV/CATV/DBS STANDBY/ON 4. Enter manufacturer’s code using 3.Enter manufacturer’s code using buttons 1-9,and1.Press and hold VCR STANDBY/ON 2.Press VCR buttons 1–9,and 1.Press and hold VCR STANDBY/ON 2.Press DVD 3. Enter manufacturer’s code using4. Release AUDIO ON 1. Press and hold AUDIO ON. STANDBY ON Manufactures’ codes for DBS tuner 1. Set the LEARN/TRANSMIT Storing the Remote Signals ManuallyMAIN ROOM/SUB ROOM selector to “LEARN.” control •Repeat steps 3 to 5 to store more signals in adifferent remote mode source Notes To use the stored signals 3. Press the desired buttonTo erase the stored signals 1. Set the LEARN/TRANSMIT PROBLEM TroubleshootingSOLUTION POSSIBLE CAUSE Continuous hissing or buzzing during FM reception Specifications 120 W per channel, min. RMS, driven into 8 Ω,Amplifier FM tuner IHF Tuning RangeAM tuner General Authorized Service Centers AccessoriesHOW TO LOCATE YOUR JVC SERVICE CENTER Do not service the television yourself WHAT YOU MUST DO FOR WARRANTY SERVICE LIMITED WARRANTYWHAT IS NOT COVERED AUDIO-2 VICTOR COMPANY OF JAPAN, LIMITED 0701NHMMDWJEIN