Adjusting the DSP Parameters —DSPPARAMETER

7 Adjustment procedure on this submenu

1 Press Þor % (DOWN or UP) to select the channel—

Adjusting the DSP Parameters —DSP PARAMETER (3)

	FRONT, CENTER, SURROUND, or SURROUND BACK,
	then press SET.
	The adjustment screen of the selected item appears.
2	Press Þ or %(DOWN or UP) to select an item you want to
	adjust on the selected adjustment screen.
3	Press # or @(RIGHT or LEFT) to adjust the item.
	• Once one of the sound levels—“BASS LEVEL,” “MID
	LEVEL” and “TREBLE LEVEL”—is adjusted, the

DSP PARAMETER

EFFECT LEVEL :3

ROOM	SIZE	:3
LIVENESS		:3
WALL	TYPE	:3

SEAT POSITION:1

:OPERATE :BACK

Note:

On this submenu, you can adjust DSP parameters.

•This submenu is available only when the DSP mode* is on, and the settings made apply only to the DSP mode* (*except All Channel Stereo).

	PARAMETRIC EQ indicator lights up on the display.
4	Repeat steps 2 and 3 to adjust the other items on the same
	adjustment screen.
5	Press EXIT once.
	The PARAMETRIC EQ submenu appears again.
6	Repeat steps 1 to 5 to adjust the other channels.

To cancel the adjustment, set all the sound levels—“BASS LEVEL,” “MID LEVEL” and “TREBLE LEVEL”—to “0 dB.” The PARAMETRIC EQ indicator goes off.

7Adjustment screen

On these adjustment screens, you can adjust the following items for each channel signal.

When the front speakers are deactivated, you cannot adjust the DSP

parameters.

7 Adjusting the DSP parameters

Select and adjust the following parameters:

EFFECT LEVEL: Adjust the DSP effect level.

As the number increases, the DSP effect becomes stronger.

(Normally select “3.” Adjustable range: 1 to 5)

ROOM SIZE: Adjust the virtual room size. As the number

increases, the interval between reflections increases so that

you will feel as if you were in a larger room. (Normally

select “3.” Adjustable range: 1 to 5)

LIVENESS: Adjust the liveness effect. As the number

increases, the attenuation level of reflections over time

decreases so that acoustics change from “Dead” to “Live.”

PEQ FRONT

BASS FREQ	:	100Hz
BASS LEVEL	:	0dB
MID FREQ	: 1.0kHz
MID LEVEL	:	0dB
TREBLE FREQ :10.0kHz
TREBLE LEVEL:		0dB
PEQ SURROUND

BASS FREQ	:	100Hz
BASS LEVEL	:	0dB
MID FREQ	: 1.0kHz
MID LEVEL	:	0dB
TREBLE FREQ :10.0kHz
TREBLE LEVEL:		0dB

PEQ CENTER

BASS FREQ	:	100Hz
BASS LEVEL	:	0dB
MID FREQ	: 1.0kHz
MID LEVEL	:	0dB
TREBLE FREQ	:10.0kHz
TREBLE LEVEL:		0dB
PEQ SURR BACK

BASS FREQ	:	100Hz
BASS LEVEL	:	0dB
MID FREQ	: 1.0kHz
MID LEVEL	:	0dB
TREBLE FREQ	:10.0kHz
TREBLE LEVEL:		0dB

(Normally select “3.” Adjustable range: 1 to 5)

WALL TYPE: Adjust the wall type. As the number increases, the

hardness of the wall to be simulated seems to become “soft” to

“hard.” (Normally select “3.” Adjustable range: 1 to 5)

SEAT POSITION: Select this to either 1 or 2 according to your

preference as if you change your seat in a theater, hall,

recital hall, church, etc.

Adjusting the Center Channel —CENTER CHANNEL (4)

BASS FREQ*	: Select the center frequency to adjust bass
	sounds from
	—63 Hz, 80 Hz, 100 Hz (initial), 125 Hz,
	160 Hz, 200 Hz, 250	Hz, 320 Hz, 400 Hz,
	500 Hz, 630 Hz, 800	Hz, 1.0 kHz

BASS LEVEL	: Adjust the enhancement level for bass sounds
	(with in the range of +6 dB to –6 dB).

MID FREQ*	: Select the center frequency to adjust
	middle-range sounds from

CENTER CHANNEL

CENTER EQ

: OFF

CENTER ALINMENT: OFF

:OPERATE :BACK

On this submenu, you can set center channel signal adjustment for the DSP modes.

•This submenu is available only when the DSP mode* is on, and the settings made apply only to the DSP mode* (*except All Channel Stereo).

	—250 Hz, 320 Hz, 400 Hz, 500 Hz, 630 Hz,
	800 Hz, 1.0 kHz (initial), 1.25 kHz, 1.6 kHz,
	2.0 kHz, 2.5 kHz, 3.2 kHz, 4.0 kHz

MID LEVEL	: Adjust the enhancement level for middle-
	range sounds (with in the range of +6 dB
	to –6 dB).

TREBLE FREQ* : Select the center frequency to adjust treble sounds from—1.0 kHz, 1.25 kHz, 1.6 kHz,

2.0kHz, 2.5 kHz, 3.2 kHz, 4.0 kHz, 5.0 kHz, 6.3 kHz, 8.0 kHz, 10.0 kHz (initial),

12.5kHz, 16.0 kHz

TREBLE LEVEL : Adjust the enhancement level for treble sounds (with in the range of +6 dB to –6 dB).

*Adjustable range changes according to the other two frequency settings.

7Cutting off the high frequency range in the center channel

Cut off the high frequency range signals in the center channel.

ON : Select this to cut off the high frequency range signals.

OFF : Select this not to cut off the high frequency range signals.

7Setting the center channel alignment

Align the vertical localization of the center channel signals (mainly human voices are recorded) at the same height as for the front speakers.

ON : Select this when you cannot feel the actors or singers are not speaking or singing on the screen.

OFF : Center channel alignment is turned off.

JVC RX-DP10VBK Adjusting the DSP Parameters —DSPPARAMETER, Adjustment procedure on this submenu

Models: RX-DP10VBK