JVC RX-DP10VBK manual control, •Repeat steps 3 to 5 to store more signals in a, Notes

TV

CATV/

DBS

4.Press one of the learning buttons, to which you want to assign a signal from the target remote

control.

The LEARN indicator starts flashing.

•If you have pressed DVD or DVD MULTI in step 3, you can store the signals into the following buttons.

			/ REW	PLAY	FF/
		EFFECT	DOWN	TUNING	UP
1	2	3		STOP	PAUSE
		ROOM SIZE
4	5	6
		LIVENESS
7/P	8	9
		WALL			SET
10	0	+10
RETURN	FM MODE	100+	DVD
			MENU

•If you have pressed PHONO in step 3, you can store the signals into the following buttons.

PLAY

TUNING

STOP

•If you have pressed CD, or CONTROL to select “ CD DISC,” in step 3, you can store the signals into the following buttons.

–You can store a different set of signals into the following buttons separately for “CD” and “CD DISC.”

			/ REW	PLAY	FF/
		EFFECT	DOWN	TUNING	UP
1	2	3		STOP	PAUSE
		ROOM SIZE
4	5	6
		LIVENESS
7/P	8	9
		WALL
10	0	+10
RETURN	FM MODE	100+

•If you have pressed “TAPE/MD” or “ CDR” in step 3, you can store the signals into the following buttons.

		EFFECT	/ REW	PLAY	FF/
1	2	3	DOWN	TUNING	UP
		ROOM SIZE	REC	STOP	PAUSE
4	5	6
		LIVENESS
7/P	8	9
		WALL
10	0	+10
RETURN	FM MODE	100+

•If you have pressed VCR1 in step 3, you can store the signals into the following buttons.

		VCR 1
		/ REW	PLAY	FF/
		STANDBY/ON
		DOWN	TUNING	UP
		REC	STOP	PAUSE
		EFFECT
1	2	3
		ROOM SIZE
4	5	6
		LIVENESS
7/P	8	9	CHANNEL
		WALL
10	0	+10
RETURN	FM MODE	100+

•If you have pressed “TV/DBS” in step 3, you can store the signals into the following buttons:

– By setting the TV operation mode selector either to “TV” or “CATV/DBS,” you can store a different set of signals into the following buttons.

TV/CATV/DBS

STANDBY/ON

		EFFECT
1	2	3	TV/VIDEO
		ROOM SIZE	TV VOL CHANNEL
4	5	6
		LIVENESS
7/P	8	9
		WALL
10	0	+10
RETURN	FM MODE	100+

5. While the LEARN indicator is flashing, press the button on the target remote control.

The signal from the target remote control is sent to this remote control.

LEARN

“LEARN OK” appears and the LEARN indicator stops flashing and remains lit. The target signal is now stored in the button selected in step 4.

Notes:

•If the LEARN indicator stops flashing before you press the button on the target remote control, repeat from step 4 again.

•If “ERROR” appears on the display, you have failed in storing the signal. Try again. However some signals do not match to this remote control even though this remote control can learn most infrared signals.

6.• Repeat steps 4 to 5 to store more signals in the same remote mode (source).

•Repeat steps 3 to 5 to store more signals in a

different remote mode (source).

7.Set the LEARN/TRANSMIT (MAIN ROOM/ SUB ROOM) selector to “TRANSMIT (MAIN ROOM/SUB ROOM)” to finish the storing procedure.

LEARN TRANSMIT	LEARN TRANSMIT
MAIN ROOM SUB ROOM	MAIN ROOM SUB ROOM
For the main room	For the sub-room
operations	operations

Notes:

•The signals stored into this remote control from the target remote control deviate slightly from the original signals. Since some components will not accept these deviating signals, you may not be able to operate those components using this remote control even though the storing procedure has been successfully finished.

•When replacing the batteries, finish it without delay; otherwise, the stored signals are all erased.

72