Open the side cover on the left side Printer | Kyocera FS-1700

1.4. Setting Up and Interfacing

2. Open the side cover on the left side of the

printer.

Side Cover

3.Insert the waste toner bottle with the bottle

tilted slightly towards you as shown in the fig- ure.

Waste Toner Bottle

4.Ensuring that it is correctly inserted, close the

side cover.

1-10

Image 31

Kyocera FS-1700 user manual Open the side cover on the left side Printer

Contents

FS-1700 FS-3700 Introduction Introduction Iii Conforming to the Class a limits FCC statement Laser safety Interface connectorsSafety information Important note on the interface connectors Laser notice Ozone concentrationCdrh regulations Vii Viii EF-1, PF-20, DU-20, HS-20 and ST-20 Declaration of Conformity Australia Canadian Department of Communications compliance statement Moving the Printer DisclaimerProlonged Non-Use and Moving the Printer Prolonged Non-use FS-3700+ Initial sleep mode setting Power consumptionKyocera ECO-PRODUCT FS-1700+ Print Engine Features Maintenance FeaturesIntroduction Xiv Software Features Guide to the Manual OptionsCD-ROM Kyocera Digital Library Xvi Table of Contents Operating the Laser Printer Setting the Audio Warning Buzzer Xix Mode Select Menu Last Clearance Positioning the PrinterPlaces to Avoid Voltage Basic requirementsCurrent capacity Unpacking and Inspection Power Supply List of shipped components Front View Names of Parts Interior View Setting Up and Interfacing Open the Top Cover Install the Toner Container Close the Top Cover Install the Waste Toner Bottle Open the side cover on the left side Printer Push the bottom plate until it locks Add Paper Open the Paper Stopper on the Face-down Output Tray Install the Face-up Output Tray if required Serial interface Attach the Power CordConnect the Printer to the Computer Parallel interface Print a Status Set the Emulation ModeTest the Interface with the Computer Windows Install the Printer Driver Windows Selecting the Multi-Purpose Tray Multi-Purpose Tray Feeding Check that the printer is Cassette mode Manual mode Envelope Feeding EnvelopesFirst ModeAutomatic Manual Feeding Overhead Projection OHP Film To remove the memory card Memory Card Handling Memory Cards Printing condition Resolution 300 dpi 600 dpi Memory Expansion InstallationRemoving the Main Circuit Board Withdrawing the Main Circuit Board from the Printer Installing SIMMs Installing and Removing SIMMsSimm to be used Removing SIMMs Testing the Expansion Memory Control Panel Operating the Laser Printer Message Meaning Interface IndicatorResolution Indicator Message Display Copy Indicator Paper Size Indicator Indicator Name Description Symbolic Indicators Key Function Control Keys Switching Power On Operating ProceduresStack Selection Feed Selection On-line/Off-line SettingAbandoning a Printing Job Status Printout Sample Status Information Installation OptionsSoftware version Hardware information User font list KIR test pattern Mode Select Menu Using the Mode Select MenuFunction Default Setting Sleep Ecopower Mode KIR Level White vertical stripes Ecoprint modeOptimized stripes Dark vertical stripes Resource Protection Adjusting the Print Density Rqvdfhu Wkhfrqwurosdqho Hints on Writing Fonts to the Memory Card Operating a Memory CardReading Fonts/Data from a Memory Card Copy TEST.TXT PRN Writing Data to a Memory Card Deleting Data from a Memory Card Formatting destroys any existing data on the memory card Formatting a Memory Card Printing a list of data names Resident Fonts Fonts Scalable fonts Bitmap fonts Kpdl Fonts List of Fonts Resident Scalable Fonts List of Fonts Kpdl Fonts Symbol set Symbol setSset value Scalable Fonts Symbol sets Toner kit replacement interval Toner Kit ReplacementToner Kit to be Used Supplying Toner Sealing Strip Remove the waste toner bottle as shown right Replace the Waste Toner Bottle Do not cap the new waste toner bottle Cleaning the Charger Wire CleaningMain Charger Unit Cleaning the Grid Paper Feed Unit If the printer does not print General GuideIf the printing is abnormal Interface Problems Power Problems Check the developer unit Print Quality ProblemsCompletely blank printout All-black printout Check the control panel Clean the charger wireDropouts, horizontal streaks, stray dots Black or white vertical streaks Grey background Check the Ecoprint settingClean the main charger wire Faint or blurred printing Characters out of position Dirt on the top edge or back of the paper Indicators Indicators and MessagesIndicator Condition Corrective Action Message Corrective Action Maintenance Messages Indicators and Messages Error Messages When memory card operations are done fromthe control panel Correcting a Paper Jam Printer Symbol Rear Cover Symbol Set Tables LaserJet 5M HP Roman-8 8U HP LaserJet 5M Symbol Sets LaserJet 5M ECMA-94 Latin 1 0N LaserJet 5M US Legal 1U LaserJet 5M IBM PC-8 10U LaserJet 5M IBM PC-8 D/N 11U LaserJet 5M IBM PC-850 12U LaserJet 5M Dutch801-RomanSWM 6N LaserJet 5M PS Math 5M LaserJet 5M PS Text 10J LaserJet 5M Math8 8M LaserJet 5M Pi Font 15U LaserJet 5M MS publishing 6J LaserJet 5M Windows 9U LaserJet 5M Desktop 7J LaserJet 5M ISO Latin 2 2N LaserJet 5M ISO Latin 5 5N LaserJet 5M Dutch801-RomanSWM 19L LaserJet 5M Dutch801-RomanSWM 26U LaserJet 5M Dutch801-RomanSWM 9J LaserJet 5M Windows Latin 1 19U LaserJet 5M Windows Latin 2 9E LaserJet 5M Windows Latin 5 5T LaserJet 5M PC-852 Latin 2 17U LaserJet 5M PC-Turkish 9T Macintosh 12J LaserJet 5M International Characters FS-1700+ FS-3700+ Printer Specifications Printer Specifications Paper Availability General Guidelines Composition Paper SpecificationsSelecting the Right Paper Condition of the Paper Thickness Caliper Basis WeightMoisture Content Smoothness Other Paper Properties Paper Grain Overhead Projection OHP Film Special Paper Label paper must be manually fed Adhesive-Backed Labels Recycled Paper EnvelopesColored Paper Preprinted Paper Parallel interface communication modes Parallel Interface Pin In/out Description Interface Signals Detailed descriptions of the signals follow Select In NSelectIn Pin RS-232C interface Interface SignalsPin In/out Signal Description RS-232C/RS-422A Interface Removing the Main Circuit Board RS-422A interface Carefully remove the jumper connector Changing the Jumper Connector Overview of Signals RS-422A Verifying the Setting RS-422A interface voltage levels Serial Connector Parameter value Baud rate RS-232C/RS-422A ProtocolParameter value Meaning Serial interface error Prescribe IIe Frpo D0 commandError not handled Error handled RS-232C Cable Connection Connecting the Printer to the ComputerPreparing an RS-232C Cable \MODE LPT1=COM1 Xiii Index Index-2 Index-3 Mode Select Menu Egjf