Operating Procedures, Switching Power On | Kyocera FS-1700 specs

2.2.Operating Procedures

2.2.Operating Procedures

Switching Power On

Check that the power cord is securely plugged in at both ends.

Check that the printer is connected to the computer. In switching power on, the general rule is to switch on printer power first, computer power second.

1. Push the power switch to the ON ( ) position.

2.Wait for the printer to warm up. During warm-up the

message display indicates .Power Switch

At the end of the warm-up period, the ON LINE indicator

lights, and the message display indicates . The printer is now ready to print.

Stack Selection

The STACK key selects the tray to which the printed pages are delivered. The STACK key can be used whenever the message display indicates .

Press the STACK key. The selection toggles and is momentarily displayed in the message display as:

# &

# &

The current selection is indicated by a green light on the printer symbol above the key.

Also, if the printer is being used with the optional sorter or stacker, the destination of the paper from each can be selected.

2-6

Image 53

Kyocera FS-1700 user manual Operating Procedures, Switching Power On, Stack Selection

Contents

FS-1700 FS-3700 Introduction Introduction Iii Conforming to the Class a limits FCC statement Safety information Interface connectorsImportant note on the interface connectors Laser safety Cdrh regulations Ozone concentrationLaser notice Vii Viii EF-1, PF-20, DU-20, HS-20 and ST-20 Declaration of Conformity Australia Canadian Department of Communications compliance statement Prolonged Non-Use and Moving the Printer DisclaimerProlonged Non-use Moving the Printer Kyocera ECO-PRODUCT Initial sleep mode setting Power consumptionFS-1700+ FS-3700+ Introduction Maintenance FeaturesPrint Engine Features Xiv Software Features CD-ROM Kyocera Digital Library OptionsGuide to the Manual Xvi Table of Contents Operating the Laser Printer Setting the Audio Warning Buzzer Xix Mode Select Menu Last Places to Avoid Positioning the PrinterClearance Current capacity Basic requirementsVoltage Unpacking and Inspection Power Supply List of shipped components Front View Names of Parts Interior View Setting Up and Interfacing Open the Top Cover Install the Toner Container Close the Top Cover Install the Waste Toner Bottle Open the side cover on the left side Printer Push the bottom plate until it locks Add Paper Open the Paper Stopper on the Face-down Output Tray Install the Face-up Output Tray if required Connect the Printer to the Computer Attach the Power CordParallel interface Serial interface Test the Interface with the Computer Set the Emulation ModePrint a Status Windows Install the Printer Driver Windows Selecting the Multi-Purpose Tray Multi-Purpose Tray Feeding Check that the printer is Cassette mode Manual mode First ModeAutomatic Manual Feeding Feeding EnvelopesOverhead Projection OHP Film Envelope To remove the memory card Memory Card Handling Memory Cards Removing the Main Circuit Board Memory Expansion InstallationPrinting condition Resolution 300 dpi 600 dpi Withdrawing the Main Circuit Board from the Printer Simm to be used Installing and Removing SIMMsInstalling SIMMs Removing SIMMs Testing the Expansion Memory Control Panel Operating the Laser Printer Resolution Indicator Interface IndicatorMessage Display Message Meaning Copy Indicator Paper Size Indicator Indicator Name Description Symbolic Indicators Key Function Control Keys Stack Selection Operating ProceduresSwitching Power On Abandoning a Printing Job On-line/Off-line SettingFeed Selection Status Printout Sample Status Software version Installation OptionsHardware information Information User font list KIR test pattern Function Default Setting Using the Mode Select MenuMode Select Menu Sleep Ecopower Mode KIR Level Optimized stripes Ecoprint modeDark vertical stripes White vertical stripes Resource Protection Adjusting the Print Density Rqvdfhu Wkhfrqwurosdqho Reading Fonts/Data from a Memory Card Operating a Memory CardHints on Writing Fonts to the Memory Card Copy TEST.TXT PRN Writing Data to a Memory Card Deleting Data from a Memory Card Formatting destroys any existing data on the memory card Formatting a Memory Card Printing a list of data names Resident Fonts Fonts Scalable fonts Bitmap fonts Kpdl Fonts List of Fonts Resident Scalable Fonts List of Fonts Kpdl Fonts Sset value Symbol setSymbol set Scalable Fonts Symbol sets Toner Kit to be Used Toner Kit ReplacementToner kit replacement interval Supplying Toner Sealing Strip Remove the waste toner bottle as shown right Replace the Waste Toner Bottle Do not cap the new waste toner bottle Main Charger Unit CleaningCleaning the Charger Wire Cleaning the Grid Paper Feed Unit If the printing is abnormal General GuideIf the printer does not print Interface Problems Power Problems Completely blank printout Print Quality ProblemsAll-black printout Check the developer unit Dropouts, horizontal streaks, stray dots Clean the charger wireBlack or white vertical streaks Check the control panel Clean the main charger wire Check the Ecoprint settingFaint or blurred printing Grey background Characters out of position Dirt on the top edge or back of the paper Indicator Condition Corrective Action Indicators and MessagesIndicators Message Corrective Action Maintenance Messages Indicators and Messages Error Messages When memory card operations are done fromthe control panel Correcting a Paper Jam Printer Symbol Rear Cover Symbol Set Tables LaserJet 5M HP Roman-8 8U HP LaserJet 5M Symbol Sets LaserJet 5M ECMA-94 Latin 1 0N LaserJet 5M US Legal 1U LaserJet 5M IBM PC-8 10U LaserJet 5M IBM PC-8 D/N 11U LaserJet 5M IBM PC-850 12U LaserJet 5M Dutch801-RomanSWM 6N LaserJet 5M PS Math 5M LaserJet 5M PS Text 10J LaserJet 5M Math8 8M LaserJet 5M Pi Font 15U LaserJet 5M MS publishing 6J LaserJet 5M Windows 9U LaserJet 5M Desktop 7J LaserJet 5M ISO Latin 2 2N LaserJet 5M ISO Latin 5 5N LaserJet 5M Dutch801-RomanSWM 19L LaserJet 5M Dutch801-RomanSWM 26U LaserJet 5M Dutch801-RomanSWM 9J LaserJet 5M Windows Latin 1 19U LaserJet 5M Windows Latin 2 9E LaserJet 5M Windows Latin 5 5T LaserJet 5M PC-852 Latin 2 17U LaserJet 5M PC-Turkish 9T Macintosh 12J LaserJet 5M International Characters FS-1700+ FS-3700+ Printer Specifications Printer Specifications Paper Availability General Guidelines Selecting the Right Paper Paper SpecificationsCondition of the Paper Composition Moisture Content Basis WeightSmoothness Thickness Caliper Other Paper Properties Paper Grain Overhead Projection OHP Film Special Paper Label paper must be manually fed Adhesive-Backed Labels Colored Paper EnvelopesPreprinted Paper Recycled Paper Parallel interface communication modes Parallel Interface Pin In/out Description Interface Signals Detailed descriptions of the signals follow Select In NSelectIn Pin Pin In/out Signal Description Interface SignalsRS-232C/RS-422A Interface RS-232C interface Removing the Main Circuit Board RS-422A interface Carefully remove the jumper connector Changing the Jumper Connector Overview of Signals RS-422A Verifying the Setting RS-422A interface voltage levels Serial Connector Parameter value Meaning RS-232C/RS-422A ProtocolParameter value Baud rate Error not handled Error handled Prescribe IIe Frpo D0 commandSerial interface error Preparing an RS-232C Cable Connecting the Printer to the ComputerRS-232C Cable Connection \MODE LPT1=COM1 Xiii Index Index-2 Index-3 Mode Select Menu Egjf