Lennox Hearth II-T C INS Planning Your Installation, Installation / Maintenance Standards

PLANNING YOUR INSTALLATION

QUESTIONS TO ASK LOCAL BUILDING OFFICIAL A correct installation is critical and imperative for reduc- ing fire hazards and perilous conditions that can arise when wood pellet burning appliances are improperly installed. The installer must follow all of the manufac- turers’ instructions.

The installation of this appliance must conform to local codes and applicable state and federal requirements. Familiarity with these requirements before installation is essential. Important considerations to discuss with local building officials include:

1.Applicable codes (i.e. Uniform Mechanical Code, State or Regional Codes).

Electrical codes:

In USA, NEC, ANSI / NFPA 70 – Latest Edition In Canada, CSA C22.1 – Latest Edition

Power Supply Requirements – The power cord must be plugged into a standard, 115 volt, 60 Hz grounded electrical outlet. The approximate power requirement is 362 Watts, and will peak up to 736 Watts for approxi- mately 6 minutes when the self-igniter is operating (it will turn off 2 minutes after flame detection). The power cord must be routed to avoid contact with any of the hot or sharp exterior surface areas of the stove. When in- stalled into a manufactured (mobile) home, the appli- ance must be electrically grounded to the steel chassis (see page 8, Manufactured [Mobile] Home Require- ments). These requirements must be met unless other- wise specified by state or local authorities.

WARNING - ELECTRICAL GROUNDING IN- STRUCTIONS: THIS APPLIANCE IS EQUIPPED WITH A THREE-PRONG (GROUNDING) PLUG FOR YOUR PROTECTION AGAINST SHOCK HAZARD AND SHOULD BE PLUGGED DI- RECTLY INTO A PROPERLY GROUNDED THREE-PRONG RECEPTACLE. DO NOT CUT OR REMOVE THE GROUNDING PRONG FROM THIS PLUG. DO NOT ROUTE POWER CORD UNDER OR IN FRONT OF APPLIANCE.

2.Local amendments?

3.Is a permit required - cost?

You may wish to contact your insurance company to ask if they require this.

4.Is outside combustion air required?

5.Rooms where the installation is not allowed?

INSTALLATION / MAINTENANCE STANDARDS

National Fire Protection Association – The primary NFPA standard that refers to installation and mainte- nance of pellet appliances and venting is NFPA 211 – Latest Edition: Chimneys, Fireplaces, Vents, and Solid Fuel appliances.

SELECTING A LOCATION

The design of your home and where you place your stove will determine its value as a source of heat. A pel- let stove depends primarily on air circulation (convec- tion) to disperse its heat, and therefore, a central loca- tion is often best. There are other practical considera- tions, which must be considered before a final selection of locations is made.

♦Existing Chimneys

♦Pellet Fuel Storage

♦Aesthetic Considerations

♦Roof Design (rafter locations & roof pitch)

♦Room Traffic

♦Proximity to Combustibles

♦Electrical Wiring

The installation of this stove will require some research. Once your options are determined, consult with your local building department who will be able to give you the necessary installation requirements for your area (Is a building permit required? Rooms where installation may not be allowed, etc.).

WARNING: CHECK ALL LOCAL BUILDING AND SAFETY CODES BEFORE INSTALLATION. THE IN- STALLATION INSTRUCTIONS AND APPROPRIATE CODE REQUIREMENTS MUST BE FOLLOWED EX- ACTLY AND WITHOUT COMPROMISE. ALTERA- TIONS TO THE STOVE ARE NOT ALLOWED. DO NOT CONNECT THE STOVE TO A CHIMNEY SYS- TEM SERVING ANOTHER STOVE, APPLIANCE, OR ANY AIR DISTRIBUTION DUCT. FAILURE TO FOL- LOW THESE INSTRUCTIONS WILL VOID THE MANUFACTURERS WARRANTY.

SMOKE DETECTORS

Since there are always several potential sources of fire in any home, we recommend installing smoke detec- tors. If possible, install the smoke detector in a hallway adjacent to the room (to reduce the possibility of occa- sional false activation from the heat produced by the stove). If your local code requires a smoke detector be installed within the same room, you must follow the re- quirements of your local code. Check with your local building department for requirements in your area.

PAGE 4

www.PelletKing.com