CARE AND OPERATION

Fuel Delivery Rate

The Heat output button manages the fuel delivery rate by controlling the amount of time the auger motor will run (Set- tings:

1 = Low, 2 Medium Low, 3 Medium, 4 Medium High, 5 High).

PRE-LIGHTING INSTRUCTIONS

During an initial start-up, or in the case where the hopper has run out of fuel, it will be necessary to prime the au- ger feed system.

To prime the auger feed tube:

1.Fill the hopper with recommended pellet fuel and plug the stove into the wall outlet.

2.Press the START button on the control board to turn on both blowers (the room air blower and exhaust blower will run at start up settings or position #3). Press the AUGER ON/OFF button on the control board to start the fuel feed. Next, press the Heat out- put button to position #5 (maximum feed rate).

3.Look through the combustion chamber door and when you see the first pellets dropping into the Ul- traGrateTM, the auger is then fully primed. It will take 10 to 15 minutes to prime the auger.

4.Once the auger is primed, press the AUGER ON/OFF button to turn off auger.

STARTING YOUR PELLET STOVE

1.Make sure the auger is primed (see Pre-Lighting Instructions above), then simply push the Start but- ton on the control board to activate the igniter.

2.Press the AUGER ON/OFF button to the “ON” posi- tion.

3.While the pellets will ignite on any heat output set- ting, it is recommended that the Heat Output be set to position #3. Pellets will start feeding into the Ul- traGrateTM and should begin to ignite in approxi- mately seven minutes. The self-igniter will auto- matically shut off after fifteen minutes.

4.After the pellets are burning well, press the HEAT OUTPUT selector to the desired setting. Combus- tion air and the pellet fuel feed rate will adjust auto- matically as the HEAT OUTPUT selector button is pressed. The flame should be bright yellow in color and there should be no evidence of soot formation at the top of the flame. Press the BLOWER SPEED control to increase or decrease the desired amount of room air from your stove.

5.If operating your stove with the wall thermostat, adjust the HEAT OUTPUT selector button to the desired demand mode (#2 through #5 on the HEAT OUTPUT selector button). Next, adjust the wall mounted thermostat to the desired heat and your stove will automatically switch between a demand mode and a pilot mode.

GENERAL OPERATING CONSIDERATIONS

Proper Burn Characteristics: Your flame should be bright yellow under normal operation. If your flame be- comes reddish/orange, your stove probably needs rou- tine maintenance. Excessive amounts of fly ash build-up in the UltraGrateTM, clinkers in the UltraGrateTM, or leak- age of air if the UltraGrateTM is not properly seated, will starve the fire for air. (See ROUTINE MAINTENANCE for information on cleaning the stove). If the problem persists, review the trouble-shooting section at the end of this manual.

Pellet Feed: The pellet feed system is designed to han- dle a wide range of pellet sizes. Different pellets can feed at considerably different rates. If the stove will not stay lit at the minimum fuel feed setting, those particular pellets may not be feeding fast enough. If this happens, adjust the damper rod (on the side of the stove) in or out to achieve a proper burn.

Pellet Size: You may notice a difference in the burn if you change pellet fuel sizes. The bigger the pellet, the slower it will feed and vice versa.

Long Burn Time: The stove may be safely operated on a continuous basis, but it is recommended that it be turned down overnight or when the room is vacated for long periods of time.

TURNING OFF YOUR PELLET STOVE

Press the AUGER ON/OFF button to the “OFF” position. This will turn the auger motor off and pellets will stop feed- ing. Both blowers will continue to operate for a period of time (up to 45 minutes) until the exhaust temperature cools sufficiently. The blowers will automatically turn off at that point.

Lighting Procedure Without Igniter: Start-up procedure when Fastfireigniter has failed or been removed and not replaced.

If your automatic ignition system should ever need trouble- shooting, repair or replacement, please contact your au- thorized Lennox Hearth Products dealer. Your stove can be lit manually without using the automatic igniter in such cases by following the procedure below.

Continued on next page…

PAGE 22

www.PelletKing.com

Page 21 Page 23
Page 22
Image 22
Lennox Hearth II-T C INS PRE-LIGHTING Instructions, Starting Your Pellet Stove, General Operating Considerations
Page 21 Page 23

II-T C FS, II-T C INS specifications

The Lennox Hearth II-T C INS and II-T C FS are exemplary models in the world of modern heating solutions, designed for efficiency, comfort, and style. With innovative engineering and advanced technology, these units cater to the needs of contemporary homeowners seeking reliable and aesthetically pleasing heating options.

One of the main features of the Lennox Hearth II-T C INS and II-T C FS is their exceptional efficiency ratings. These models are designed to operate at high efficiency levels, reducing energy consumption while providing optimal warmth. This not only translates to lower utility bills but also represents a more sustainable choice for environmentally conscious consumers.

A standout characteristic of these products is their versatility in installation. The II-T C INS is an insert model, allowing it to be fitted into existing fireplaces easily. This makes it an ideal option for homeowners wanting to upgrade their current heating systems without extensive renovations. The II-T C FS, on the other hand, is a freestanding stove that adds a classic touch to any room, making it a perfect focal point while offering powerful heating capabilities.

Both models are equipped with advanced technology designed for seamless operation. The hot air circulation system ensures that warmth is evenly distributed throughout the space, eliminating cold spots and enhancing overall comfort. In addition, their adjustable thermostats allow users to set the desired temperature with ease, ensuring a consistent indoor environment.

The Lennox Hearth units are also designed with user convenience in mind. They come with easy-to-use controls and can often be integrated with smart home systems, offering the flexibility to monitor and adjust settings remotely. This modern approach to home heating makes it simple for users to maintain a cozy atmosphere, even on the coldest days.

Moreover, Lennox places a strong emphasis on safety. These heating models include features such as a glass door that remains cool to the touch and a built-in safety shut-off system, providing peace of mind for families.

In summary, the Lennox Hearth II-T C INS and II-T C FS models stand out for their efficiency, versatility, advanced technology, and safety features. With a focus on optimal performance and user convenience, these units represent a significant advancement in home heating, making them an attractive choice for those looking to enhance their living spaces while staying warm and comfortable.
Top Page Image Contents