Front Panel Controls and Connections | Lincoln Electric IM915

b-4	OPERATION	b-4

FRONT PANEL CONTROLS AND CONNECTIONS

CASE FRONT CONTROLS

FIGURE b.1

2

6

3

	5	1	4	7	8

ITEM				DESCRIPTION

1	Status LED indicates system status.

2	Digital Meter Display is a bright LED display of key welding information. Adjusting Parameter
	Knobs.

3	MSP4 Panel is used to set the weld mode, adjust the arc, change arc start/end parameters
	and for set-up information.

4	Cold Feed - Gas Purge Switch, press the switch up to feed wire with weld output off. Press the
	switch down for gas flow with weld output off.

5	2 step - 4 step Switch is used to choose between a 2 step trigger or a 4 step trigger operation.

6	Location for Optional Memory Panel. (Order K2360-1 for the memory panel. See Accessories
	Section).

7	Cover for Optional Water Cooling Kit, remove when the water cooling kit is installed. See
	instructions with water cooling Kit.

8	Trigger Connector 5-pin amphenol for connecting the MIG gun trigger. See Installation Section
	for detail.

POWER FEED™ 10M SINGLE WIRE FEEDER

Image 26

Lincoln Electric IM915 manual Front Panel Controls and Connections

Contents

Power Feed 10M Single Wire Feeder July Safety Depends on You Safety Electric Shock can kill Welding and Cutting Sparks can Cause fire or explosion Iii Précautions DE Sûreté Thank You TAbLE of Contents Vii Power Feed 10M Single Wire Feeder SPEC.# Type Input PowerTemperature Rating Welding Capacity Rating Mounting Electric Shock can killLocation Weld CAbLE SIzING Electrode Work Power SourceCOAxIAL Weld CAbLES DIP Switch #7 Position Polarity Negative Electrode Polarity Power Source Pin Function Welding Gun/Wire Feeder Trigger ConnectorWire Feeder Wire Feeder Pin Function Changing Drive Rolls and Wire Guides Description Drive Roll Pressure Setting Changing the GUN Receiver bUSHING Magnum GUN and CAbLE ASSEMbLIES Welding GUNS, Torches and ACCES- SoriesGUN Receiver bUSHING To change the gear ratio Wire Feed Shut Down CircuitChanging the Gear Ratio Spindle Placement Wire Reel LoadingDIP Switch #8 Position Gear Ratio Loading 16 to 44 lb .3 20kg Spools Using K1504-1 Coil Reel Figure A.10 Removing a Readi-Reel Weld Wire RoutingLoading 30 lb .6 kg Readi-Reels See Figure A.11 BUILDUP OF SHIELDING GAS may harm health or kill Shielding GAS ConnectionCylinder may explode if damaged ExAMPLES of Connecting AN Arclink Power Wave System ARC Rays can burn Fumes and Gases can be dangerousWelding Sparks can cause fire or explosion Common Welding AbbREVIATIONS Required Equipment Product DescriptionRecommended Processes Additional Required Equipment CV Welding Pulse Welding or STT Welding Front Panel Controls and Connections Status LED Synergic CV Voltage Display Volts / Trim DisplayPrior to Welding LAYOUT-CONTROLS see Figure b.3 Mode Select Panel 4 MSP4Overview LAYOUT-DIGITAL Display Changing ARC Wave Control POWER-UP SequenceChanging Weld Modes Infrared IR Control Accessing the Machine Setup Menu Limit SettingMachine SETUP/USER Preferences SET-UP Features Menu Figure b.3a Setup Menu User Defined Parameters Parameter Definition Procedure Change Method Stall Factor Adjustment Reset Consumable Weight Parameter Definition Gun Offset AdjustmentCrater Delay TIG Gas Control Display Trim as Volts Option Arc Start/Loss Error TimeParameter Definition Push-Pull Gun Knob behavior Sense From Studs Parameter Definition Show Test Modes 100 View Diagnostics107 View Power Source Protocol 102 View Fatal Logs 505 Setup Menu Lock 503 Memory button Disable504 Mode Select Panel Lock Parameter Definition 501 Encoder Lockout 509 UI Master Lockout Only be accessed using Power Wave Manager softwareParameter Definition 506 Set User Interface Passcode Step Trigger Operation Cold Feed / GAS Purge SwitchStep / 4-STEP Trigger Switch Step Trigger Operation Sequence of Operation Figure b.5 Modes Process Setup and OperationNon- Synergic Steel and Stainless Synergic GMAW-P Pulsed MIG Welding ARC Control Pulse-on-Pulse Welding Machine Functionality bY Weld Process CC Stick Modes CV GMAW/FCAW NON-SYNERGIC Output Control KNObS, Weld Mode 5Process Weld Mode CV NON-SYNERGIC Modes Synergic CV Modes Wire SIzE 030 035 045 052Gmaw Synergic Material Process GAS Pulse and PULSE-0N-PULSE Modes Wire SIzEPulse and PULSE-ON-PULSE Synergic WIR E S IZE MAW-S TT WE L D ModeSTT and STT II NONN-SYNERGIC 035 045 052 Touch Start TIG Gtaw TIG WeldingGtaw Touch Start TIG Welding All Metals Touch Start TIG User Memories Weld Mode SearchingSearching for a Weld Mode Limit Setting Enable Accessories Optional Accessories Lb. coils to 2 spindles Periodic Maintenance Safety PrecautionsRoutine Maintenance CALIbRATION Specification TROUbLESHOOTING POSSIbLE PRObLEMSSymptoms Cause Recommended Course of Action Arclink System Error Codes Your local Lincoln Authorized Output PRObLEMS TROUbLESHOOTING PRObLEMS POSSIbLE Power Feed 10M Single Wire Feeder 14.56 18.48 15.80 30.46 Power Feed 10M Single Wire Feeder Power Feed 10M Single Wire Feeder Precaucion Warnung