SET-UP Features Menu | Lincoln Electric IM915 specification

b-10	OPERATION	b-10

	SETUP MENU FEATURES

The Setup Menu gives access to the Setup Configuration. Stored in the setup configuration are user parameters that generally only need to be set at installation. The parameters are grouped as shown in the following table.

PARAMETER	DEFINITION
P.1 through P.99	Unsecured Parameters (always adjustable)
P.100 through P.107	Diagnostic Parameters (always read only)

SET-UP FEATURES MENU

(See Figure B.3a)

1.To access the set-up menu, press the Right and Left buttons of the MSP4 panel simultaneously. Note that the set-up menu cannot be accessed if the system is welding, or if there is a fault (The sta- tus LED is not solid green).

Change the value of the blinking parameter by rotat- ing the SET knob.

2.After changing a parameter it is necessary to press the Right hand button to save the new setting. Pressing the Left button will cancel the change.

3.To exit the set-up menu at any time, press the Right and Left buttons of the MSP4 panel simulta- neously. Alternately, 1 minute of inactivity will also exit the set-up menu.

FIGURE b.3a - SETUP MENU

	Mode Select
2	Panel (MSP4)

6

3

Left				Right
button		SET Knob		button
5	1	SET Knob		8
	1	4	7	8

LED

Indicator

POWER FEED™ 10M SINGLE WIRE FEEDER

Image 32

Lincoln Electric IM915 manual SET-UP Features Menu, Figure b.3a Setup Menu

Contents

Power Feed 10M Single Wire Feeder July Safety Depends on You Safety Electric Shock can kill Welding and Cutting Sparks can Cause fire or explosion Iii Précautions DE Sûreté Thank You TAbLE of Contents Vii SPEC.# Type Input Power Temperature RatingPower Feed 10M Single Wire Feeder Welding Capacity Rating Electric Shock can kill LocationMounting Weld CAbLE SIzING Electrode Work Power SourceCOAxIAL Weld CAbLES DIP Switch #7 Position Polarity Negative Electrode Polarity Welding Gun/Wire Feeder Trigger Connector Wire FeederPower Source Pin Function Wire Feeder Pin Function Changing Drive Rolls and Wire Guides Description Drive Roll Pressure Setting Changing the GUN Receiver bUSHING Magnum GUN and CAbLE ASSEMbLIES Welding GUNS, Torches and ACCES- SoriesGUN Receiver bUSHING To change the gear ratio Wire Feed Shut Down CircuitChanging the Gear Ratio Wire Reel Loading DIP Switch #8 Position Gear RatioSpindle Placement Loading 16 to 44 lb .3 20kg Spools Using K1504-1 Coil Reel Figure A.10 Removing a Readi-Reel Weld Wire RoutingLoading 30 lb .6 kg Readi-Reels See Figure A.11 BUILDUP OF SHIELDING GAS may harm health or kill Shielding GAS ConnectionCylinder may explode if damaged ExAMPLES of Connecting AN Arclink Power Wave System Fumes and Gases can be dangerous Welding Sparks can cause fire or explosionARC Rays can burn Common Welding AbbREVIATIONS Product Description Recommended ProcessesRequired Equipment Additional Required Equipment CV Welding Pulse Welding or STT Welding Front Panel Controls and Connections Status LED Synergic CV Voltage Display Volts / Trim DisplayPrior to Welding Mode Select Panel 4 MSP4 OverviewLAYOUT-CONTROLS see Figure b.3 LAYOUT-DIGITAL Display POWER-UP Sequence Changing Weld ModesChanging ARC Wave Control Infrared IR Control Accessing the Machine Setup Menu Limit SettingMachine SETUP/USER Preferences SET-UP Features Menu Figure b.3a Setup Menu User Defined Parameters Parameter Definition Procedure Change Method Stall Factor Adjustment Parameter Definition Gun Offset Adjustment Crater DelayReset Consumable Weight TIG Gas Control Arc Start/Loss Error Time Parameter Definition Push-Pull Gun Knob behaviorDisplay Trim as Volts Option Sense From Studs 100 View Diagnostics 107 View Power Source ProtocolParameter Definition Show Test Modes 102 View Fatal Logs 503 Memory button Disable 504 Mode Select Panel Lock505 Setup Menu Lock Parameter Definition 501 Encoder Lockout 509 UI Master Lockout Only be accessed using Power Wave Manager softwareParameter Definition 506 Set User Interface Passcode Step Trigger Operation Cold Feed / GAS Purge SwitchStep / 4-STEP Trigger Switch Step Trigger Operation Sequence of Operation Figure b.5 Modes Process Setup and OperationNon- Synergic Steel and Stainless Synergic GMAW-P Pulsed MIG Welding ARC Control Pulse-on-Pulse Welding Machine Functionality bY Weld Process CC Stick Modes Output Control KNObS, Weld Mode 5 Process Weld ModeCV GMAW/FCAW NON-SYNERGIC CV NON-SYNERGIC Modes Wire SIzE 030 035 045 052 Gmaw SynergicSynergic CV Modes Material Process GAS Pulse and PULSE-0N-PULSE Modes Wire SIzEPulse and PULSE-ON-PULSE Synergic MAW-S TT WE L D Mode STT and STT II NONN-SYNERGICWIR E S IZE 035 045 052 Gtaw TIG Welding Gtaw Touch Start TIG WeldingTouch Start TIG All Metals Touch Start TIG User Memories Weld Mode SearchingSearching for a Weld Mode Limit Setting Enable Accessories Optional Accessories Lb. coils to 2 spindles Safety Precautions Routine MaintenancePeriodic Maintenance CALIbRATION Specification TROUbLESHOOTING PRObLEMS SymptomsPOSSIbLE Cause Recommended Course of Action Arclink System Error Codes Your local Lincoln Authorized Output PRObLEMS TROUbLESHOOTING PRObLEMS POSSIbLE Power Feed 10M Single Wire Feeder 14.56 18.48 15.80 30.46 Power Feed 10M Single Wire Feeder Power Feed 10M Single Wire Feeder Precaucion Warnung