|
| OPERATION | ||||
|
|
|
|
|
|
|
|
|
|
| USER DEFINED PARAMETERS |
|
|
|
|
|
|
|
| |
|
|
|
|
|
| |
|
| Parameter | Definition |
|
| |
|
| P.99 | Show Test Modes |
|
| |
|
|
|
| Most power sources contain weld modes used for calibration and test purposes. By default, the machine |
| |
|
|
|
| does not include test weld modes in the list of weld modes that are available to the operator. To manually |
| |
|
|
|
| select a test weld mode, set this option to "Yes". When the power source is turned off and back on again, |
| |
|
|
|
| the test modes will no longer appear in the mode list. Test weld modes typically require the machine out- |
| |
|
|
|
| put to be connected to a grid load and cannot be used for welding. |
|
|
|
|
|
|
|
| |
|
| P.100 | View Diagnostics |
|
| |
|
|
|
| Diagnostics are only used for servicing or troubleshooting the Power Wave system. |
| |
|
|
|
| Select "Yes" to access the diagnostic options in the menu. Additional parameters will |
| |
|
|
|
| now appear in the setup menu (P.101, P.102, etc). |
|
|
|
|
|
|
|
| |
|
| P.101 | View Event Logs |
|
| |
|
|
|
| Used for viewing all the system event logs. Press the Right Button to enter the option. Rotate Control |
| |
|
|
|
| Knob to select the desired event log to read. Press the Right Button again to enter the selected log. |
| |
|
|
|
| Rotating the Control Knob will scroll through the event log, displaying the log index number, event code |
| |
|
|
|
| and some other data. Press the Left Button to back out to select another log. Press the Left Button again |
| |
|
|
|
| to exit this option. |
|
|
|
|
|
|
|
| |
|
| P.102 | View Fatal Logs |
|
| |
|
|
|
| Used for viewing all the system fatal logs. Press the Right Button to enter the option. Rotate Control Knob |
| |
|
|
|
| to select the desired fatal log to read. Press the Right Button again to enter that log. Rotating the Control |
| |
|
|
|
| Knob will scroll through the log, displaying the log index number and fatal code. Press the Left Button to |
| |
|
|
|
| back out to select another log. Press the Left Button again to exit this option. |
|
|
|
|
|
|
|
| |
|
| P.103 | View Software Version Information |
|
| |
|
|
|
| Used for viewing the software versions for each board in the system. Press the Right Button to |
| |
|
|
|
| enter the option. Rotate Control Knob to select the desired board to read. Press the Right |
| |
|
|
|
| Button again to read the firmware version. Press the Left Button to back out to select another |
| |
|
|
|
| board. Rotate the Control Knob to select another board, or press the Left Button to exit this |
| |
|
|
|
| option. |
|
|
|
|
|
|
|
| |
|
| P.104 | View Hardware Version Information |
|
| |
|
|
|
| Used for viewing the hardware version for each board in the system. Press the right MSP |
| |
|
|
|
| Button to enter the option. Rotate Set knob to select the desired board to read. Press the right |
| |
|
|
|
| button again to read the hardware version. Press the left button to back out to select another |
| |
|
|
|
| board. Press the left button again to exit this option. |
|
|
|
|
|
|
|
| |
|
| P.105 | View Welding Software Information |
|
| |
|
|
|
| Used for viewing the Weld Set in the Power Source. Press the Right Button to read the Weld |
| |
|
|
|
| Set version. Press the Left Button to back out and exit this option. |
|
|
|
|
|
|
|
| |
|
| P.106 | View Ethernet IP Address |
|
| |
|
|
|
| Used for viewing the IP address of Ethernet compatible equipment. Press the Right Button to |
| |
|
|
|
| read the IP Address. Press the Left Button to back out and exit this option. The IP address can- |
| |
|
|
|
| not be changed using this option. |
|
|
|
|
|
|
|
| |
|
| P.107 | View Power Source Protocol |
|
| |
|
|
|
| Used for viewing the type of power source the feeder is connected to. Press the Right Button to |
| |
|
|
|
| identify the power source as either LincNet or ArcLink. Press the Left Button to back out and |
| |
|
|
|
| exit this option. |
|
|
|
|
|
|
|
|
|
