Lb. coils to 2 spindles | Lincoln Electric IM915 specification

C-3				ACCESSORIES				C-3


			K162-1	Spindle Adapter, for Readi-Reels	Includes: Spindle Assemble
				and 2" ID spools up to 60 lb.	with locking clip.

			K435	Spindle Adapter, for mounting 14	Includes: Spindle Adapter
				lb. Innershield Coils on 2" spindles.	made from 2 coil retainers.
					(Electrode not included.)

			K468	Spindle Adapter, for mounting 8"	Includes: Spindle Adapter.
				dia. spools on 2" spindles.

			K363P	Readi-Reel Adapter, for mounting	Includes: Readi-Reel spool
				23-30 lb. reels to 2" spindles.	adapter. (Spool of electrode
					not included.)

			K438	Readi-Reel Adapter, for mounting	Includes: Readi-Reel spool
				50-60 lb. reels to 2" spindles.	adapter. (Spool of electrode
					not included.)

			K1504-1	Coil Adapter, for mounting 50-60	Includes:	50-60 lb. coil
				lb. coils to 2" spindles.	adapter.

K1634-3	Plastic Wire Cover for 30-44 lb.	Includes: Cover, backing
	Wire packages.	plate, wire conduit, incoming
		bushing for .025 - 1/16" wire,
		incoming bushing for 1/16" -
		1/8" wire, thumb screw,
K1634-2	Plastic Wire Cover for up to 60 lb.	mounting hardware
	Wire packages.	and hex key.

K590-6	Water Connection Kit	Includes: 2 hoses, 4 quick dis-
		connect fittings, hose clamps
		and mounting hardware.

POWER FEED™ 10M SINGLE WIRE FEEDER

Image 57

Lincoln Electric IM915 manual Lb. coils to 2 spindles

Contents

Safety Depends on You Power Feed 10M Single Wire Feeder July Safety Electric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosion Précautions DE Sûreté Thank You TAbLE of Contents Vii Temperature Rating SPEC.# Type Input PowerPower Feed 10M Single Wire Feeder Welding Capacity Rating Location Electric Shock can killMounting Weld CAbLE SIzING Power Source COAxIAL Weld CAbLESElectrode Work Negative Electrode Polarity DIP Switch #7 Position Polarity Wire Feeder Welding Gun/Wire Feeder Trigger ConnectorPower Source Pin Function Wire Feeder Pin Function Description Changing Drive Rolls and Wire Guides Changing the GUN Receiver bUSHING Drive Roll Pressure Setting Welding GUNS, Torches and ACCES- Sories GUN Receiver bUSHINGMagnum GUN and CAbLE ASSEMbLIES Wire Feed Shut Down Circuit Changing the Gear RatioTo change the gear ratio DIP Switch #8 Position Gear Ratio Wire Reel LoadingSpindle Placement Loading 16 to 44 lb .3 20kg Spools Figure A.10 Using K1504-1 Coil Reel Weld Wire Routing Loading 30 lb .6 kg Readi-Reels See Figure A.11Removing a Readi-Reel Shielding GAS Connection Cylinder may explode if damagedBUILDUP OF SHIELDING GAS may harm health or kill ExAMPLES of Connecting AN Arclink Power Wave System Welding Sparks can cause fire or explosion Fumes and Gases can be dangerousARC Rays can burn Common Welding AbbREVIATIONS Recommended Processes Product DescriptionRequired Equipment Additional Required Equipment CV Welding Pulse Welding or STT Welding Front Panel Controls and Connections Status LED Volts / Trim Display Prior to WeldingSynergic CV Voltage Display Overview Mode Select Panel 4 MSP4LAYOUT-CONTROLS see Figure b.3 LAYOUT-DIGITAL Display Changing Weld Modes POWER-UP SequenceChanging ARC Wave Control Infrared IR Control Limit Setting Machine SETUP/USER PreferencesAccessing the Machine Setup Menu Figure b.3a Setup Menu SET-UP Features Menu User Defined Parameters Stall Factor Adjustment Parameter Definition Procedure Change Method Crater Delay Parameter Definition Gun Offset AdjustmentReset Consumable Weight TIG Gas Control Parameter Definition Push-Pull Gun Knob behavior Arc Start/Loss Error TimeDisplay Trim as Volts Option Sense From Studs 107 View Power Source Protocol 100 View DiagnosticsParameter Definition Show Test Modes 102 View Fatal Logs 504 Mode Select Panel Lock 503 Memory button Disable505 Setup Menu Lock Parameter Definition 501 Encoder Lockout Only be accessed using Power Wave Manager software Parameter Definition 506 Set User Interface Passcode509 UI Master Lockout Cold Feed / GAS Purge Switch Step / 4-STEP Trigger SwitchStep Trigger Operation Sequence of Operation Step Trigger Operation Figure b.5 Process Setup and Operation Non- SynergicModes ARC Control Steel and Stainless Synergic GMAW-P Pulsed MIG Welding Pulse-on-Pulse Welding CC Stick Modes Machine Functionality bY Weld Process Process Weld Mode Output Control KNObS, Weld Mode 5CV GMAW/FCAW NON-SYNERGIC CV NON-SYNERGIC Modes Gmaw Synergic Wire SIzE 030 035 045 052Synergic CV Modes Material Process GAS Wire SIzE Pulse and PULSE-ON-PULSE SynergicPulse and PULSE-0N-PULSE Modes STT and STT II NONN-SYNERGIC MAW-S TT WE L D ModeWIR E S IZE 035 045 052 Gtaw Touch Start TIG Welding Gtaw TIG WeldingTouch Start TIG All Metals Touch Start TIG Weld Mode Searching Searching for a Weld ModeUser Memories Limit Setting Enable Optional Accessories Accessories Lb. coils to 2 spindles Routine Maintenance Safety PrecautionsPeriodic Maintenance CALIbRATION Specification TROUbLESHOOTING Symptoms PRObLEMSPOSSIbLE Cause Recommended Course of Action Arclink System Error Codes Your local Lincoln Authorized Output PRObLEMS TROUbLESHOOTING PRObLEMS POSSIbLE Feeder Power Feed 10M Single Wire 30.46 14.56 18.48 15.80 Power Feed 10M Single Wire Feeder Power Feed 10M Single Wire Feeder Precaucion Warnung