Manuals / Lincoln Electric / Power Tools / Welder

Lincoln Electric IM915 Parameter Definition 506 Set User Interface Passcode, UI Master Lockout

Models: IM915

1 72

Page 39

b-17		OPERATION	b-17

		USER DEFINED PARAMETERS


	Parameter	Definition
	P.506	Set User Interface Passcode
		Prevents unauthorized changes to the equipment. The default passcode is zero which allows full access.
		A nonzero passcode will prevent unauthorized: changes to memory limits, saving to memory (if P.502 =
		Yes), changes to setup parameters (if P.505 = Yes).
		This parameter can only be accessed using Power Wave Manager software.

	P.509	UI Master Lockout
		Locks all user interface controls, preventing the operator from making any changes. This parameter can
		only be accessed using Power Wave Manager software.

POWER FEED™ 10M SINGLE WIRE FEEDER

Page 39

Image 39

Lincoln Electric IM915 manual Parameter Definition 506 Set User Interface Passcode, UI Master Lockout

Contents

Safety Depends on You Power Feed 10M Single Wire Feeder July Safety Electric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosion Précautions DE Sûreté Thank You TAbLE of Contents Vii Welding Capacity Rating SPEC.# Type Input PowerTemperature Rating Power Feed 10M Single Wire Feeder Weld CAbLE SIzING Electric Shock can killLocation Mounting Power Source COAxIAL Weld CAbLESElectrode Work Negative Electrode Polarity DIP Switch #7 Position Polarity Wire Feeder Pin Function Welding Gun/Wire Feeder Trigger ConnectorWire Feeder Power Source Pin Function Description Changing Drive Rolls and Wire Guides Changing the GUN Receiver bUSHING Drive Roll Pressure Setting Welding GUNS, Torches and ACCES- Sories GUN Receiver bUSHINGMagnum GUN and CAbLE ASSEMbLIES Wire Feed Shut Down Circuit Changing the Gear RatioTo change the gear ratio Loading 16 to 44 lb .3 20kg Spools Wire Reel LoadingDIP Switch #8 Position Gear Ratio Spindle Placement Figure A.10 Using K1504-1 Coil Reel Weld Wire Routing Loading 30 lb .6 kg Readi-Reels See Figure A.11Removing a Readi-Reel Shielding GAS Connection Cylinder may explode if damagedBUILDUP OF SHIELDING GAS may harm health or kill ExAMPLES of Connecting AN Arclink Power Wave System Common Welding AbbREVIATIONS Fumes and Gases can be dangerousWelding Sparks can cause fire or explosion ARC Rays can burn Additional Required Equipment Product DescriptionRecommended Processes Required Equipment CV Welding Pulse Welding or STT Welding Front Panel Controls and Connections Status LED Volts / Trim Display Prior to WeldingSynergic CV Voltage Display LAYOUT-DIGITAL Display Mode Select Panel 4 MSP4Overview LAYOUT-CONTROLS see Figure b.3 Infrared IR Control POWER-UP SequenceChanging Weld Modes Changing ARC Wave Control Limit Setting Machine SETUP/USER PreferencesAccessing the Machine Setup Menu Figure b.3a Setup Menu SET-UP Features Menu User Defined Parameters Stall Factor Adjustment Parameter Definition Procedure Change Method TIG Gas Control Parameter Definition Gun Offset AdjustmentCrater Delay Reset Consumable Weight Sense From Studs Arc Start/Loss Error TimeParameter Definition Push-Pull Gun Knob behavior Display Trim as Volts Option 102 View Fatal Logs 100 View Diagnostics107 View Power Source Protocol Parameter Definition Show Test Modes Parameter Definition 501 Encoder Lockout 503 Memory button Disable504 Mode Select Panel Lock 505 Setup Menu Lock Only be accessed using Power Wave Manager software Parameter Definition 506 Set User Interface Passcode509 UI Master Lockout Cold Feed / GAS Purge Switch Step / 4-STEP Trigger SwitchStep Trigger Operation Sequence of Operation Step Trigger Operation Figure b.5 Process Setup and Operation Non- SynergicModes ARC Control Steel and Stainless Synergic GMAW-P Pulsed MIG Welding Pulse-on-Pulse Welding CC Stick Modes Machine Functionality bY Weld Process CV NON-SYNERGIC Modes Output Control KNObS, Weld Mode 5Process Weld Mode CV GMAW/FCAW NON-SYNERGIC Material Process GAS Wire SIzE 030 035 045 052Gmaw Synergic Synergic CV Modes Wire SIzE Pulse and PULSE-ON-PULSE SynergicPulse and PULSE-0N-PULSE Modes 035 045 052 MAW-S TT WE L D ModeSTT and STT II NONN-SYNERGIC WIR E S IZE All Metals Touch Start TIG Gtaw TIG WeldingGtaw Touch Start TIG Welding Touch Start TIG Weld Mode Searching Searching for a Weld ModeUser Memories Limit Setting Enable Optional Accessories Accessories Lb. coils to 2 spindles CALIbRATION Specification Safety PrecautionsRoutine Maintenance Periodic Maintenance TROUbLESHOOTING Cause Recommended Course of Action PRObLEMSSymptoms POSSIbLE Arclink System Error Codes Your local Lincoln Authorized Output PRObLEMS TROUbLESHOOTING PRObLEMS POSSIbLE Feeder Power Feed 10M Single Wire 30.46 14.56 18.48 15.80 Power Feed 10M Single Wire Feeder Power Feed 10M Single Wire Feeder Precaucion Warnung

OPERATION

USER DEFINED PARAMETERS

Parameter

Definition

P.506

Set User Interface Passcode

P.509

UI Master Lockout

only be accessed using Power Wave Manager software.

POWER FEED™ 10M SINGLE WIRE FEEDER