TOC
TOC
ElEcTrical DiaGramS | ||
SchEmaTic - cOmplETE machiNE - (S28101) |
|
|
Section
Master
S28101 | ENGINEERING CONTROLLED | |
MANUFACTURER: | No | |
CHANGE DETAIL: REVISED RHEOSTAT & ROTOR LOAD INFORMATION. ADDED RHEOSTAT VALUE.
Return to
Return to
STATOR | L1 - REACTOR |
W1 | Located inside backof control box. |
| |
WELD | 60 VAC |
@ MAX | |
WINDING | RHEOSTAT/ |
| NO LOAD |
W2 |
|
WELD OUTPUT
W1A 
STUDS
60VAC
@MAX
RHEOSTAT/
NO LOAD
B = BLACK |
| Y = YELLOW | |
O = ORANGE |
| Y/R = YELLOW/RED STRIPE | |
N/C = NO CONNECTION | B/Y = BLACK/YELLOW STRIPE | ||
| IF OIL LEVEL IS TOO LOW OIL LEVEL | ||
| SWITCH CLOSES GROUNDING | ||
| ENGINE MAGNETO VIA OIL LEVEL | ||
| MODULE PREVENTING ENGINE | ||
N/C | N/C FROM STARTING OR RUNNING. | ||
Y | Y/R | Locatedinsideengine blower housing. | |
to Section TOC
to Master TOC
GROUND STUD ON |
|
|
|
|
|
| |||||
|
|
|
|
|
| ||||||
CONTROL PANEL FRONT | |||||||||||
Circuit Breaker located |
|
|
|
|
|
|
| ||||
|
|
|
|
|
| ||||||
|
|
|
| ||||||||
oncontrol panel upper |
|
|
|
|
|
| |||||
right handcorner. |
|
| CB1 | ||||||||
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| 20A | |||
Located insideenginecrankcase.
O
OIL LEVEL
GND
SWITCH
MODULE | B | ENGINE |
| |
MAGNETO |
| |||
(OIL LEVEL) |
| |||
IGNITION | SPARK | |||
B/Y |
| |||
STOP RUN |
| PLUG | ||
|
|
| ||
SWITCH
Return
3 | 3 |
|
| |
|
| 3A | ||
130 VAC@ MAX |
| |||
RHEOSTAT/ |
|
| ||
5NO LOAD | 5A |
|
| |
5 |
|
| ||
130 VAC |
|
| 5B | |
@ MAX | NEUTRAL STUD |
| ||
RHEOSTAT/ | CB1 |
| ||
ON CONTROL |
| |||
NO LOAD | 20A | 6A | ||
6 | PANEL BOTTOM | |||
|
3B
J5
5A 
SILVER 
120 VAC
Receptaclelocatedon control panel
6B
J6 |
240 VAC |
GENERATOR
FRAME
GROUND
ENGINE
FOOT
205
Locatedon topof engineblower housing, right hand as viewedfrombehindmachine
FLASHING AMPS TO ROTOR WITH GENERATOR LEAD 7 DISCONNECTED AND ENGINE RUNNING AT 3700 RPM = 0.15 TO 0.25 AMPS
Return to Section TOC
Return to Master TOC
EXCITER WINDING
7 |
35 VAC |
MAX |
RHEOSTAT |
201B |
|
|
200 |
| |
| AC |
|
(+) | D2 | |
3.3 Ohms/ 100 Watt
RHEOSTAT
200A | Rheostat located |
| oncontrol panel. |
CW
Excitationrectifier locatedin enclosure on sheet metal
FLASH FROM
ENGINE MAGNETO
202B 
202
| + |
|
|
AC | D3 | AC | N/C 600 uf |
| - | Flashing rectifier and | |
|
| filter capacitor | |
|
| locatedin enclosure | |
202C
202A
+37.5 TO 42.5
VDC MAX
RHEOSTAT
MAX RHEOSTAT FIELD AMPS =
5.75TO 6.0 @ 75 deg F
4.25TO 4.5 @ OPERATING TEMPERATURE
9
| AC |
200C |
|
Hourmeter locatedon | HOUR |
control panel upper | METER |
left hand corner. |
near rectifier
201
201C
N/C | behindcontrol panel |
in moldedplastic mountingbracket.
| 201A |
| REVOLVING FIELDS |
201D | (ROTOR) |
| 7 OHMS @ 75vF |
| 9 OHMS @ OPERATING |
| TEMPERATURE |
Return to Section TOC
Return to Master TOC
PROPRIETARY & CONFIDENTIAL:THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OWNED BY LINCOLN GLOBAL, INC. AND MAY NOT BE DUPLICATED, COMMUNICATED TO OTHER PARTIES OR USED FOR ANY PURPOSE WITHOUT THE EXPRESS WRITTEN PERMISSION OF LINCOLN GLOBAL, INC.
MANUFACTURING TOLERANCE PER E2056 | CONTROL: CLEVELAND | SCALE: | EQUIPMENT TYPE: |
|
| BULLDOG 140 |
|
|
|
| |||
UNLESS OTHERWISE SPECIFIED TOLERANCE: |
|
|
| PAGE ___ OF ___ | |||||||||
ON 2 PLACE DECIMALS IS ± .02 in. (± 0.5 mm) |
|
| NONE |
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
| 1 | 1 | |
ON 3 PLACE DECIMALS IS ± .002 in. (± 0.05 mm) | DRAWN BY: | mpatrzyk |
|
|
|
|
|
|
|
|
|
|
|
IF PRINTED | SUBJECT: |
|
| MACHINE SCHEMATIC | DOCUMENT |
| DOCUMENT | ||||||
MATERIAL TOLERANCE ("t") TO AGREE | ENGINEER: | APM | @ A4 SIZE |
|
| NUMBER: |
| REVISION: | |||||
ON ALL ANGLES IS ± .5 OF A DEGREE |
|
|
|
|
|
|
|
|
|
| S28101 |
| B |
WITH PUBLISHED STANDARDS. |
|
|
|
|
|
|
|
|
|
|
| ||
|
| UNITS: | MATERIAL | UF | APPROVAL |
|
| PROJECT | REFERENCE: |
| |||
|
|
|
| ||||||||||
DO NOT SCALE THIS DRAWING | APPROVED: | DRS | INCH | DISPOSITION: | DATE: | 7/31/2009 |
| S28100 |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual.
