Linksys BEFW11S4 Instant Wireless Series, Wireless Access Point Router with 4-Port Switch, Enable

Models: BEFW11S4

1 59
Download 59 pages 56.17 Kb
Page 34
Image 34
4. I am not able to access the Router’s web interface Setup page.

Instant Wireless® Series

F.Turn off the computer, Router, and cable/DSL modem. Wait 30 seconds, and then turn on the Router, cable/DSL modem, and computer. Check the Status tab of the Router’s web-based utility to see if you get an IP address.

4. I am not able to access the Router’s web interface Setup page.

A.Refer to “Problem #2, I want to test my Internet connection” to verify that your computer is properly connected to the Router.

B.Refer to “Appendix D: Finding the MAC Address and IP address for Your Ethernet Adapter” to verify that your computer has an IP Address, Subnet Mask, Gateway, and DNS.

C.Set a static IP address on your system; refer to “Problem #1: I need to set a static IP address.”

D.Refer to “Problem #10: I need to remove the proxy settings or the dial-up pop-up window (for PPPoE users).”

5.I can’t get my Virtual Private Network (VPN) working through the Router.

Access the Router’s web interface by going to http://192.168.1.1 or the IP address of the Router, and go to the Advanced => Filter tab. Make sure you have IPsec pass-through and/or PPTP pass-through enabled.

VPNs that use IPSec with the ESP (Encapsulation Security Payload known as protocol 50) authentication will work fine. At least one IPSec session will work through the Router; however, simultaneous IPSec sessions may be possible, depending on the specifics of your VPNs.

VPNs that use IPSec and AH (Authentication Header known as protocol 51) are incompatible with the Router. AH has limitations due to occasional incom- patibility with the NAT standard.

Change the IP address for the Router to another subnet to avoid a conflict between the VPN IP address and your local IP address. For example, if your VPN server assigns an IP address 192.168.1.X (X is a number from 1 to 254) and your local LAN IP address is 192.168.1.X (X is the same number used in the VPN IP address), the Router will have difficulties routing information to the right location. If you change the Router’s IP address to 192.168.2.1, that should solve the problem. Change the Router’s IP address through the Setup tab of the web interface. If you assigned a static IP address to any computer or net- work device on the network, you need to change its IP address accordingly to 192.168.2.Y (Y being any number from 1 to 254). Note that each IP address must be unique within the network.

Wireless Access Point Router with 4-Port Switch

Your VPN may require port 500/UDP packets to be passed to the computer that is connecting to the IPSec server. Refer to “Problem #7, I need to set up online game hosting or use other Internet applications” for details.

Check the Linksys website for more information at www.linksys.com.

6. I need to set up a server behind my Router.

To use a server like a web, ftp, or mail server, you need to know the respective port numbers they are using. For example, port 80 (HTTP) is used for web; port 21 (FTP) is used for FTP, and port 25 (SMTP outgoing) and port 110 (POP3 incoming) are used for the mail server. You can get more information by viewing the documentation provided with the server you installed. Follow these steps to set up port forwarding through the Router’s web-based utility. We will be setting up web, ftp, and mail servers.

A.Access the Router’s web-based utility by going to http://192.168.1.1 or the IP address of the Router. Go to the Advanced => Forwarding tab.

B.Enter any name you want to use for the Customized Application.

C.Enter the Ext. Port range of the service you are using. For example, if you have a web server, you would enter the range 80 to 80.

D.Check the protocol you will be using, TCP and/or UDP.

E.Enter the IP address of the PC or network device that you want the port server to go to. For example, if the web server’s Ethernet adapter IP address is 192.168.1.100, you would enter 100 in the field provided. Check “Appendix D: Finding the MAC Address and IP Address for Your Ethernet Adapter” for details on getting an IP address.

F.Check the Enable option for the port services you want to use. Consider the example below:

Customized

Ext. Port

TCP

UDP

IP Address

Enable

Application

 

 

 

 

 

Web server

80 to 80

X

X

192.168.1.100

X

FTP server

21 to 21

X

 

192.168.1.101

X

SMTP (outgoing)

25 to 25

X

X

192.168.1.102

X

POP3 (incoming)

110 to 110

X

X

192.168.1.102

X

When you have completed the configuration, click the Apply button.

59

60

Page 34
Image 34
Linksys BEFW11S4 manual Instant Wireless Series, I am not able to access the Router’s web interface Setup page, Enable