Static IP | Linksys BEFW11S4 specification

Instant Wireless® Series

Static IP

If your ISP says that you are connecting through a static (or fixed) IP address, select this option from the drop-down menu (as shown in Figure 5- 4). The Router will utilize that static IP Address when the following infor- mation is entered into the appropriate field:

Figure 5-4

•WAN IP Address and Subnet Mask This is the Router’s IP Address and Subnet Mask as seen by external users on the Internet (including your ISP).

•Default Gateway Address Your ISP will provide you with the Gateway IP Address.

•DNS (Domain Name Server) IP Address Your ISP will provide you with at least one DNS IP Address.

Wireless Access Point Router with 4-Port Switch

PPPoE

Some DSL-based ISPs use PPPoE ( Po i n t - t o - Po i n t

Protocol over Ethernet) to estab- lish communica- tions with an end- user. If you are using a DSL line, check with your ISP to see if they use PPPoE. If they do use PPPoE, select this from the drop- down menu (as shown in Figure 5- 5).

Figure 5-5

If you do enable PPPoE, remember to remove any existing PPPoE applica- tions already on any of your PCs.

•User Name and Password Enter the User Name and Password you use when logging onto your ISP connection.

•Connect on Demand and Max Idle Time You can configure the Router to disconnect your ISP connection after a specified period of time (Max Idle Time). If you have been disconnected due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio button. If you want your Internet con- nection to remain on at all times, enter 0 in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet access disconnects.

•Keep Alive Option and Redial Period This option keeps you connected to your ISP indefinitely, even when your connection sits idle. To use this option, click the radio button next to Keep Alive. The default Redial Period is 30 seconds.

25

26

Image 17

Linksys BEFW11S4 manual Static IP

Contents

Wireless Access Point Router With 4-Port Switch Copyright & Trademarks Industry Canada Canada Table of Contents Features Linksys Wireless Access Point Router with 4-Port SwitchIntroduction Minimum Requirements IP Addresses Dhcp Dynamic Host Configuration Protocol ServersWhat’s an IP Address? Static IP Addresses Power Wireless Access Point Router’s PortsWireless Access Point Router’s LEDs Ports WAN Indicators Connecting the RouterConnecting Your Hardware Together and Booting Up Before You Start Instant Wireless Series Overview Configuring the PCsConfiguring Windows 95, 98, and Millennium PCs Configuring Windows 2000 PCs Configuring Windows XP PCs A b l e / D i s a b l e Configuring the Router Static IP Obtain an IP AutomaticallyAddress PPPoE Pptp Using the Router’s Web- Based Utility Setup Static IP Status Password Dhcp Log AOL Parental Controls Security Filters Help Editing MAC Filter Setting Setting Up FiltersUsing Multicast Pass Through Advanced Tab Filters Using Pptp Pass Through Using IPSec Pass ThroughUsing Remote Management Using Remote Upgrade Advanced Tab Port Range Forwarding UPnP Forwarding Instant Wireless Series Advanced Tab Dynamic Routing Port Triggering Advanced Tab Static Routing Advanced Tab MAC Address Cloning Advanced Tab DMZ Host Advanced Tab Wireless Need to set a static IP address on a PC Appendix a TroubleshootingCommon Problems and Solutions For Windows XP For Windows NTWant to test my Internet connection For Windows 95, 98, and Me For Windows XP Need to set up a server behind my Router Am not able to access the Router’s web interface Setup Can’t get the Internet game, server, or application to work Need to upgrade the firmware To start over, I need to set the Router to factory defaultFirmware upgrade failed, and/or the Diag LED is flashing My DSL service’s PPPoE is always disconnecting Need to use port triggering Click the Advanced = Filter tabDiag LED stays lit continuously Full/Col LED keeps flickering continuously Frequently Asked Questions Allows Pptp packets to pass through Instant Wireless Series Step Two Pinging for a Web Address Appendix B How to Ping Your ISP’s E-mail and Web AddressesStep One Pinging an IP Address Appendix C Configuring Wireless Security Figure C-2 Figure C-3 Configuring Wireless Security in Windows XP Figure C-6 Figure C-10 For Windows NT, 2000, and XP Figure D-3 Http//192.168.1.1 in the web Figure D-6 AOL Broadband via DSL Figure E-3 Appendix F Glossary Instant Wireless Series Instant Wireless Series Instant Wireless Series 100 102 104 Environmental Appendix G Specifications Web site FTP site Appendix H Warranty InformationAppendix I Contact Information Copyright 2003 Linksys, All Rights Reserved