Set up speakers (Audyssey® Auto Setup)
Error messages
NOTE
•An error message is displayed if Audyssey® Auto Setup could not be completed due to speaker placement, the measurement environment, etc. If this happens, check the relevant items, be sure to take the necessary measures, then perform Audyssey® Auto Setup over again.
•If the result still differs from the actual connection status after remeasurement or the error message still appears, it is possible that the speakers are not connected properly. Turn this unit off, check the speaker connections and repeat the measurement process from the beginning.
•Be sure to turn off the power before checking speaker connections.
| Examples |
|
|
|
|
| Error details | Measures | |||||
|
|
|
|
|
|
|
| • The connected setup microphone is broken, or a device other than the | • Connect the included setup microphone to the SETUP MIC jack of this unit. | ||||
| Audyssey Auto Setup |
| MultEQ |
| |||||||||
|
|
| supplied setup microphone is connected. |
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Caution! |
|
|
|
|
| • Check the speaker connections. | ||||||
|
|
|
|
|
| • Not all speakers could be detected. | |||||||
| Microphone or Speaker is none |
|
|
|
|
| |||||||
|
|
|
|
|
| • The front L speaker was not properly detected. |
|
|
|
|
| ||
| Retry |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Audyssey Auto Setup |
| MultEQ | • There is too much noise in the room for accurate measurements to be | • Either turn off any device generating noise or move it away. | ||||||||
|
| made. | • Perform again when the surroundings are quieter. | ||||||||||
|
|
|
|
|
|
|
| ||||||
| Caution! |
|
|
|
|
| |||||||
|
|
|
|
|
| • Speaker or subwoofer sound is too low for accurate measurements to be | • Check the speaker installation and the direction in which the speakers are | ||||||
|
|
|
|
|
|
|
| ||||||
| Ambient noise is too high or level is too low | made. | facing. | ||||||||||
|
|
|
|
|
|
|
|
| • Adjust the subwoofer’s volume. | ||||
| Retry |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Audyssey Auto Setup |
| MultEQ | • The displayed speaker could not be detected. | • Check the connections of the displayed speaker. | ||||||||
|
| (The screen on the left indicates that the front right speaker cannot be |
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Caution! Speaker:None |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| detected.) |
|
|
|
|
| ||
| Front R |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| ||
| Retry |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Audyssey Auto Setup |
| MultEQ | • The displayed speaker is connected with the polarity reversed. | • Check the polarity of the displayed speaker. |
|
| ||||||
|
| (The screen on the left indicates that the polarity phases of the front right | • For some speakers, this error message may be | ||||||||||
|
|
|
|
|
|
|
| ||||||
| Caution! Speaker:Phase |
|
|
|
|
| |||||||
|
|
|
|
|
| speakers are reversed.) | displayed even if the speaker is properly connected. | ||||||
|
|
|
|
|
|
|
| ||||||
| Front R |
|
|
|
|
|
|
| If you are sure the connection is correct, press ui | ||||
|
|
|
|
|
|
|
| ||||||
| Skip |
|
|
|
|
|
| to select “Skip”, then press ENTER. | |||||
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
| ||
| Retry |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
version Basic
version Advanced
Information
16