LCD PWB Sheet | Matsushita CF-08TX1A1M specs

LCD PWB Sheet

Parts for electricity removing work

Refrect Tape

Press the Sheet along the

edge of the Reflector (Avoid floating.).

0~0.5mm

Standard attaching position of 1

Match to the PWC outline.

CN

Run over the end of the CN metal (0.5 to 1 mm)

Attach here.

Lengthwise: Match to the top end of the Reflector.

Crosswise: Match to the rib of the Frame.

Bend to the lateral side.

Pet Tape 1

Match to the Kapton side and attach to the Reflector side.(Do not remove the Release Paper other than the Paper of the attaching part.)

TS Noise Tape

A

0~1mm

Holder sheet

edge standard: +0.5 mm

-

LCD PWB SPACER ASSY

Insert between Board and LCD Frame.

LCD PWB SPACER ASSY

Spacer LCD PWB Spacer Spacer Sheet

Sheet	Asymmetric shape
	The form of the left and
	the right isn’t symmetrical.

Screw

View from A direction

0~1mm

Holder sheet

edge standard: +0.5 mm

-

Screw

9-9

Image 33

Matsushita CF-08TX1A1M manual LCD PWB Sheet

Contents

CF-08TX1A1M Page Page Avoid Heat PrecautionsAvoid Extreme Heat, Cold and Direct Sun- light Do Not Put into a Micro- wave Stop Using Contents Main Specifications Specifications Bluetooth Wireless LAN Introduction CopyrightDisclaimer Trademarks Stylus holder Security lock Speaker Expansion bus connector Battery pack Headphone jackDescription of parts Microphone jack Attaching the Tether Using the Tether Turn on the wireless display Starting up/Shutting DownConnect to the server When terminating the connection Make the settings only for the SupervisorWhen settings have been changed When deleting settings Shutting Down power off the wireless display Diagnosis & Repair Flow Chart Troubleshooting Self Test Program CPU Type checkSdram march test Test register check for the source microcomputer ID check for 2700GChip ID check for LAN9118 How to Restart Starting Up TroubleshootingDisplay Touchscreen Connecting Peripherals Wireless CommunicationShut Down Sound Block Diagram DC/DC VCC5P0V LCD FET Dock CON PCB Wiring Connection Diagram Removing the Battery Pack Disassembly/ReassemblyPreparation Removing the Display Unit Removing the Main PCB Removing IO Power PCB Removing the Wlan PCB Removing the Speaker Removing the Audio Con PCBRemoving the USB PCB Removing the Wlan L PCB Removing the Bluetooth Wlan R PCBRemoving the Dock Con PCB Removing the SW LED PCB Removing the LCD Unit and the Inverter Setting the LCD Unit and the Inverter Reassembly Instructions Preparations for backlight Safety Working LCD PWB Sheet Preparations for Touchscreen Assembly of the LCD Block Setting the SW LED PCB Assembly of the SW LED PCB Setting the Dock Con PCB Assembly of the Dock CON PCB Setting the Wlan L PCB Setting the Bluetooth Wlan R PCB Setting the USB PCB Setting the SpeakerSetting the Audio Con PCB Setting the IO Power PCB Setting the Wlan PCB Setting the Main PCB USB PCB FFC Setting the Display Unit Assembly of the Display unit Cable Hold Sheet Setting the Battery Pack Battery Pack Slide the knob to the outside and lock firmly 10-1 Exploded View 10-2 10-3 11-1 Replacement Parts List 11-2 11-3 REF. no and Area 11-4 11-5 11-6 11-7 11-8 11-9 11-10 11-11 11-12 11-13 11-14 Resistor Array 11-15 11-16 11-17 11-18 11-19 ERJ3GEYJ562V 11-20 11-21 11-22 11-23 CF-08 Printed Circuit Board Main PCB SW LED PCB RJ45LAN CF-08 Schematic Diagram IO Power 1 I/F Connector For Cradle DC-IN IO Power 2 DCIN/ Battery LTC4008EGN#TRPBF IO Power 3 Charger SENSE2 IO Power 4 VA3,VA5 ECFlash IO Power 5 EC IO Power 6 Overprotect Wlan 1 SYCHIPWLAN/ BT Board Wlan 2 SYCHIPWLAN/ BT Board