Assembly of the Dock CON PCB | Matsushita CF-08TX1A1M specs

■Assembly of the DOCK CON PCB

Order of fixing

Screw-1->Screw-5

Screw-4

Screw-3

Screw-5

Screw-1

Caption Tape

Attach the Hook firmly.Ensure the Connector Terminals of the Sheet ( Docking PCB sheet) do not run over.

(Attach in the arrow direction Screw-2horizontally.)

Match to the end of the

Connector. (0 to 1 mm)

Base Joint Cover

Match to the center of Mg square hole. (– 1 mm)

Ensure the direction is right.

Check Insert/Lock.

stiffening plate side

Cradle

Relay Card

		FFC
	Docking PCB Sheet	(Docking Card)
	Docking PCB Sheet
	Attach.	Busterade
		Busterade
	0~1mm	Rear Case Assy
	FFC Hold Cushion
	Attach to the	10+1mm
	top side of CN.	10+1mm
	top side of CN.

Docking

PCB side

Asymmetric shape

Docking Cover Sheet

9-14

Image 38

Matsushita CF-08TX1A1M manual Assembly of the Dock CON PCB

Contents

CF-08TX1A1M Page Page Avoid Extreme Heat, Cold and Direct Sun- light PrecautionsAvoid Heat Do Not Put into a Micro- wave Stop Using Contents Specifications Main Specifications Wireless LAN Bluetooth Disclaimer Trademarks IntroductionCopyright Description of parts Battery pack Headphone jackStylus holder Security lock Speaker Expansion bus connector Microphone jack Using the Tether Attaching the Tether Connect to the server Turn on the wireless displayStarting up/Shutting Down When settings have been changed Make the settings only for the SupervisorWhen terminating the connection When deleting settings Shutting Down power off the wireless display Flow Chart Diagnosis & Repair Troubleshooting Sdram march test Self Test ProgramCPU Type check Chip ID check for LAN9118 Test register check for the source microcomputerID check for 2700G How to Restart Display TroubleshootingStarting Up Touchscreen Shut Down Wireless CommunicationConnecting Peripherals Sound Block Diagram DC/DC VCC5P0V LCD FET Wiring Connection Diagram Dock CON PCB Preparation Disassembly/ReassemblyRemoving the Battery Pack Removing the Display Unit Removing IO Power PCB Removing the Main PCB Removing the USB PCB Removing the Wlan PCB Removing the SpeakerRemoving the Audio Con PCB Removing the Dock Con PCB Removing the Bluetooth Wlan R PCBRemoving the Wlan L PCB Removing the SW LED PCB Removing the LCD Unit and the Inverter Reassembly Instructions Setting the LCD Unit and the Inverter Preparations for backlight Safety Working LCD PWB Sheet Preparations for Touchscreen Setting the SW LED PCB Assembly of the LCD Block Assembly of the SW LED PCB Setting the Dock Con PCB Assembly of the Dock CON PCB Setting the Bluetooth Wlan R PCB Setting the Wlan L PCB Setting the Audio Con PCB Setting the USB PCBSetting the Speaker Setting the Wlan PCB Setting the IO Power PCB Setting the Main PCB USB PCB FFC Setting the Display Unit Assembly of the Display unit Cable Hold Sheet Setting the Battery Pack Battery Pack Slide the knob to the outside and lock firmly Exploded View 10-1 10-2 10-3 Replacement Parts List 11-1 11-2 11-3 11-4 REF. no and Area 11-5 11-6 11-7 11-8 11-9 11-10 11-11 11-12 11-13 11-14 11-15 Resistor Array 11-16 11-17 11-18 11-19 11-20 ERJ3GEYJ562V 11-21 11-22 11-23 CF-08 Printed Circuit Board Main PCB SW LED PCB CF-08 Schematic Diagram IO Power 1 I/F Connector RJ45LAN IO Power 2 DCIN/ Battery For Cradle DC-IN IO Power 3 Charger LTC4008EGN#TRPBF IO Power 4 VA3,VA5 SENSE2 IO Power 5 EC ECFlash IO Power 6 Overprotect Wlan 1 SYCHIPWLAN/ BT Board Wlan 2 SYCHIPWLAN/ BT Board