Maytag MGR6875ADB/Q/S/W manual Moving and/or Replacing Range, Leveling Legs, Anti-Tip Bracket

Disassembly Procedures

!WARNING

To avoid risk of electrical shock, personal injury, or death: disconnect electrical and gas supply before servicing.

Moving and/or Replacing Range

1.Turn off electrical power and gas supply to the range.

2.Slide range forward from installation position.

3.Unplug power cord and disconnect gas line from unit.

4.Replace range using Installation Instructions.

NOTE: When placing range into installation position verify anti-tip bracket(s) are engaged.

Leveling Legs

•Some floors are not level.

•For proper baking, your range must be level.

•Leveling legs are located on each corner of the base of the range.

•Place a level horizontally on an oven rack and check front-to-back and side-to-side. Level by turning the legs.

Anti-Tip Bracket

When ever range is moved or replaced for safety reasons this bracket must be engaged.

Anti-Tip Bracket

Leveling Leg

Top Burner

Maintop Removal

1.Disconnect power before servicing.

2.Remove surface burner control knobs by grasping knob and raising knob straight upward.

3.Remove screws securing infinite switch bracket to maintop.

4.Remove screws securing burner assemblies to maintop.

5.Remove screws securing maintop to chassis. Screws are located in the front left and right corners with the upper oven door open.

6.Remove screws securing ground strap to chassis.

7.Raise and remove maintop from unit.

8.Reverse procedures to reassemble.

Top Surface Valve and Spark Switch

1.Remove maintop, see "Maintop Removal" procedure. (Perform steps 1 – 6.)

2.Remove spark switch(es) by pulling upward off valve.

3.Remove wires from spark switch by depressing release arm.

4.Remove bolt(s) securing surface valve(s) to manifold. Located on the bottom of manifold.

5.Reverse procedures to reassemble.

NOTE: Perform gas leak test.

Shut-Off Valve

1.Remove maintop, see "Maintop Removal" procedure. (Perform steps 1 – 6.)

2.Remove screws securing back panel to chassis.

3.Disconnect tubing to shut-off valve.

4.Remove bolt securing shut-off valve to manifold.

5.Reverse procedures to reassemble.

1.	Disconnect power before servicing.	NOTE: Perform gas leak test.
2.	Remove screws securing burner to burner lower	Top Burner Lower Assembly
	assembly.
		1.	Remove maintop, see "Maintop Removal" procedure.
3.	Reverse procedures to reassemble.
			(Perform steps 1 – 6.)
Side Panel
		2.	Disconnect tubing from lower assembly.
NOTE: Removal of range from installation position is		3.	Reverse procedures to reassemble.
		NOTE: Perform gas leak test.
	required.
1.	Disconnect power before servicing.	Manifold and Top Burner
2.	Remove range from installation position, see "Move	1.	Remove maintop, see "Maintop Removal" procedure.
	and/or Replacing Range" procedure.
			(Perform steps 1 – 6.)
3.	Remove maintop, see "Maintop Removal" procedure.
		NOTE: If replacing manifold only, skip step 2.
	(Perform steps 1 – 6.)
4.	Remove screws securing right side panel at the top	2.	Loosen and disconnect fittings securing surface
	and back of panel.		burner tubing to burner assembly and manifold.
5.	Pull side panel outward away from rear of range,	3.	Remove bolt(s) securing surface valve(s) to
	then lift upward on the side panel to release from		manifold.
	slotted clips located in front and set aside.	4.	Remove bolt securing shut-off valve from manifold.
6.	Reverse procedures to reassemble.	5.	Disconnect tubing from manifold to the regulator.
		6.	Reverse procedures to reassemble.
		NOTE: Perform gas leak test.
24	16023415		©2004 Maytag Services