Middleby Marshall PS200-R68 Middleby, Marshall, Section Installation, At All Times

VI. ELECTRIC SUPPLY FOR GAS HEATED OVENS

Electric supply for all gas heated ovens is 208-240 volts AC single phase. Each oven requires a separate 15 amp service. Connection is made as shown in Figures 2-8 & 2-12. A separate ground wire must also be supplied.

CAUTION: Before connecting incoming power to oven, a voltage reading of each leg to neutral must be made. These readings should not normally exceed 120 volts each.

If one of the incoming legs reads over 130 volts, this indicates the supply voltage has a high leg.

Export ovens are supplied with a stepdown transformer for the 110V control circuit.

Call your local electrician or electrical power supply company and have them remove the high leg from the electrical supply line for the oven.

Connecting a high leg to the black lead of the oven will severely damage many of the electrical components in the oven.

CONNECTING A HIGH LEG TO THE BLACK WIRE VOIDS ALL OVEN WARRANTIES.

SECTION 2

INSTALLATION

Connect one 208-240V supply leg to the black wire and the other 208-240V supply leg to the red wire. The supply neutral should connect to the white oven wire and supply ground should connect to the oven ground screw located in the main junction box.

VII. ELECTRICAL CONNECTION

INFORMATION FOR ALL OVENS.

Check the oven data plate before making any electrical connections. Connections must agree with data on oven data plate (Refer below to Figure 2-11).

NOTE: In Canada with C22.1,Part 1 and/or local code.

A fused disconnect switch or circuit breaker (not fur- nished) MUST be installed in the electrical supply line FOR EACH OVEN. A lockout/tagout electrical shutoff must be installed for each oven, refer to Figure 2-9. The service connection must meet all national and local electrical code requirements. All connections are made at one common connection at the back of each control box.

NOTE:

When the oven is installed it must be electrically grounded in accordance with local codes, or in the absence of local codes. ANSI/NFPA - Latest edition.

WARNING

OVEN MUST BE KEPT CLEAR

OF COMBUSTIBLES

AT ALL TIMES.

CAUTION

IT IS REQUIRED THAT THE OVEN BE PLACED UNDER A VENTILATION HOOD FOR ADEQUATE AIR SUPPLY

AND VENTILATION

CAUTION:

The power burner will not operate and gas will not flow through the burner without electric power. No attempt should be made to operate the oven during power failure.This oven is to be operated only on the type of gas as shown on the specification data plate.

Middleby

SUITABLE FOR INSTALLATION ON COMBUSTIBLE FLOORS ADJACENT

EIGHTEEN INCHES TO RIGHT SIDE WALL, SIX INCHES TO BACK WALL.

TO COMBUSTIBLE AND NONCOMBUSTIBLE WALLS WITH THE FOLLOW-

Marshall

ING MINIMUM CLEARANCES: ZERO INCHES TO LEFT SIDE WALL,

"INTENDED FOR OTHER THAN HOUSEHOLD USE"

A MIDDLEBY COMPANY

FOR INSTALLATION UNDER VENTILATING HOOD ONLY

MODEL NO.

SERIAL NO.

DESIGN

ID NO.

TYPE OF GAS

ACCEPTED FOR USE

MERICA

CITY OF NEW YORK

A

N

DEPARTMENT OF BUILDINGS

INPUT BTU PER HOUR MAXIMUM

MEA 309-83-E

G

S

S

A

N

CANADIAN GAS ASSOCIATION

A

S

O

IO

A T

MAN. PRESS.

IN.W.C.

WIRE WITH GROUND

C

C I

R

APPROVED

ERTIFIE

D

VAC

AMPS

AMPS

HZ

MANUFACTURED UNDER U.S. PATENT NUMBERS 3,844,213 AND 4,154,861

ELGIN, ILLINOIS, 60120, U.S.A. COMMERCIAL OVEN ANS Z 83.12

DATA PLATE FOR OVENS WITH THE MACHINERY/DRIVE COMPARTMENT LOCATED AT THE RIGHT END OF OVEN

Middleby

SUITABLE FOR INSTALLATION ON COMBUSTIBLE FLOORS ADJACENT

EIGHTEEN INCHES TO LEFT SIDE WALL, SIX INCHES TO BACK WALL.

TO COMBUSTIBLE AND NONCOMBUSTIBLE WALLS WITH THE FOLLOW-

Marshall

ING MINIMUM CLEARANCES: ZERO INCHES TO RIGHT SIDE WALL,

"INTENDED FOR OTHER THAN HOUSEHOLD USE"

A MIDDLEBY COMPANY

FOR INSTALLATION UNDER VENTILATING HOOD ONLY

MODEL NO.

SERIAL NO.

DESIGN

ID NO.

TYPE OF GAS

ACCEPTED FOR USE

A

ERIC

AN

CITY OF NEW YORK

M

DEPARTMENT OF BUILDINGS

G S

INPUT BTU PER HOUR MAXIMUM

MEA 309-83-E

S

A

N

CANADIAN GAS ASSOCIATION

A

S

O

IO

A T

MAN. PRESS.

IN.W.C.

WIRE WITH GROUND

C

C I

R APPROVED

ERTIFIE

D

VAC

AMPS

AMPS

HZ

MANUFACTURED UNDER U.S. PATENT NUMBERS 3,844,213 AND 4,154,861

ELGIN, ILLINOIS, 60120, U.S.A. COMMERCIAL OVEN ANS Z 83.12

DATA PLATE FOR OVENS WITH THE MACHINERY/DRIVE COMPARTMENT LOCATED AT THE LEFT END OF OVEN

Figure 2-11.

Oven Specifi-

cation Data

Plate Refer-

ence

19