Mitsubishi Electronics R100 Using a Hub, Chapter 3 - Software Configuration

Chapter 3 - Software Configuration

Firmware Restoration

This utility will automatically search out failed R100 Wireless Gateways and upload a firmware that you specify. The process takes about 3 to 4 minutes and during this process the PWR, AIR, and WAN LEDs will remain lit while the LAN LED will flash slowly.

The Firmware Restoration utility is an emergency rescue tool to restore a R100 which has failed during a previous firmware upload. A failed firmware upgrade will cause the R100 to enter a failure mode, waiting for the user to use the Firmware Restoration utility to find and upload a new firmware. This is not a firmware upgrade utility and cannot be used on a working R100 Wireless Gateway. Normal firmware upgrades must be done through the web manager.

Utilities .3

Using a Hub

If you have problems uploading a firmware while using a network hub, try connecting your computer directly to the LAN port of the R100. Either 10Base-T or 100Base-TX connections will work.

74	R100 Wireless Gateway

Contents

Page R100 Wireless Gateway Table of Contents Page Page Disclaimer Chapter 1 - Introduction Overview System Requirements •Wireless Connectivity and backwards compatibility •Secure wireless connectivity •Multiple local network ports •Broadband port •Shared Intenet access •USB device support •Printer sharing •Easy setup and management Network Topology Network Backbone Agent to an ISP Agent to Another Network PWR (Power) AIR (Wireless Network) WAN (Wide Area Network) LAN 1-4(Local Area Network) Installation Chapter 2 - Installation LAN Connection: Power Connection: Printer Connection: USB Connection: Page Page Wired Connection Wireless-Connection default Printer Connection Chapter 3 - Software Configuration Configuring the R100 Wireless Gateway Setting an IP address for the Wired or Wireless Connection Getting the IP Automatically Setting an IP Address Manually setup.exe Finish 1. Wireless Gateway Utilities 2. Connect to the WLAN Web Manager Configure User Name & Password Home Page 3. Set your own password 4. Use Quick Install Operation Mode Quick Setup Quick Setup in Wireless Gateway Mode Middle: High: Save&Restart Page Wireless Interface SSID Channel Auto Wireless Mode Auto 54G Only TKIP: AES: 64/128-bitversus 40/104-bit Passphrase TKIP AES WEP-64bits WEP-128bits WEP Key Key Index key rotation Network Key Rotation Interval Bridge AP Mode Channel Connect to APs in Remote Bridge List (Yes/No) Allow anonymous? (Yes/No) MAC Address Access Control Adding a MAC Address MAC Address Add Radius Setting Server IP Address – Server Port – Connection Secret – Advanced DTIM Interval (1~255) – Beacon Interval (1~65535) – Enable Frame Bursting? – Enable Radio Date to Enable Radio WAN & LAN WAN Connection Type Static IP PPPoE PPTP DNS Server 1/DNS Server PPPoE or PPTP Account PPPoE or PPTP User Name Password DNS and WINS Server Setting Assign IP Address Manually Manually Assigned IP List MAC Address Add Del Route Apply to routing table Static Route List Network/Host IP Netmask Miscellaneous Enable UPnP Remote Log Server Time Zone NTP Server DDNS Setting Dynamic DNS Enable the DDNS Client Yes Server NAT Settings Port Trigger Enable Port Trigger Well Known Applications Trigger Port List Virtual Server List Virtual DMZ Basic Configuration LAN to WAN Filter (Outgoing Traffic) WAN to LAN Filter LAN to WAN Filter Table and WAN to LAN Filter Table URL Filter FTP Server Encrypted files are not supported Force to Eject USB Disk Enable FTP Server Yes Login as Anonymous: Login User Account List Max. Login Rights Read/Write/Erase: Read/Write: User Account and Privileges Banned IP List Client Setting Web Camera 2.Select Tools->Internet Options->Security->Local Intranet Custom Level GotoInternetOptionsfromthe Toolsmenu Page Web Camera vs. DDNS Security Mode Setting Enable Security Mode Date to Enable Security Mode Time to Enable Security Mode Page Wireless Gateway Router Access Point Router Apply Home Quick Setup in Router Mode Router Apply Home Quick Start Access Point Apply Quick Setup in Access Point Mode Configure Wireless Interface IP Config in Access Point Mode IP Config LAN Get IP Automatically Status System Setup Change Password admin Save Page Setting Management Save As a File HERE Save Target As Load From a File Factory Default Restoring Factory Default Settings Web Manager Factory Default Restore Hardware DHCP Leases Port Forwarding Routing Table System Log Using a Hub Installing the Printer Driver (2)Choose Install by the Add Printer Wizard computer Page Printer Custom Settings… Add Standard TCP/IP Printer Port Wizard and go back to AddPrinter Wizard AddPrinterWizard Printer Setup Wizard Printer Setup Wizard Start-->Program-->R100 Wireless Gateway add a Standard TCP/IP port. Refer to Verifying Your Printer Verifying Your Printer (Cont’) Chapter 4 - Wireless Performance Performance Appendix -Troubleshooting Problem Solution Reset Restore Factory Default Advanced Setup Name Page http://www.MitsubishiElectric.com.au Firmware Upgrade Appendix - Glossary Broadband Client Device name DHCP (Dynamic Host Configuration Protocol) - This protocol allows Frame-bursting Firewall Gateway Handshaking IEEE PC Card PPP (Point-to-Point WAN (Wide Area Network) Appendix - GNU General Public License Availability of source code GNU GENERAL PUBLIC LICENSE Preamble Terms & conditions for copying, distribution, & modification Page Page Page Page NO WARRANTY Australian Service Contacts www.mitsubishielectric.com.au New South Wales and Australian Capital Territory Queensland South Australia and Northern Territory Western Australia New Zealand Web site: www.bdt.co.nz