WI1370
System Troubles
| Keypad Beeps or | Zone LED | System Trouble | Cause/Action |
|
| H SYSTEM | ON | Condition |
|
|
|
|
|
|
| |
| Flashes |
|
|
|
|
|
|
|
|
|
|
| 1 Beep | 1 | Y AC Power Failure | This trouble will occur if AC power is not present. Ensure that the transformer is connected to an unswitched power source. |
|
| Y LED |
|
|
| |
|
|
|
|
| |
|
|
|
|
|
|
|
| 2 | Low Battery | If there has been a recent power failure, the battery may be partially depleted and must be recharged by the control panel. If |
|
|
|
|
| the trouble does not go away in 24 hours, replace the battery. |
|
|
|
|
|
|
|
|
| 3 | Communication | The system was not able to report to central station. Check panel programming and telephone line wiring. The trouble will |
|
|
|
| Failure/PCPreset Fail | clear after it has been acknowledged by viewing the system trouble as long as the telephone line has passed a line cut test |
|
|
|
| (tested automatically by the panel). The Panel did not sucsessfully connect and download/upload with the commputer |
| |
|
|
|
| running PCPreset - check Auto Download ID number, Callback Number or PCPreset Setup. |
|
|
| 4 | Telephone Line Cut | The telephone line has failed. If telephone service has been temporarily interrupted, the trouble will clear when restored and |
|
|
|
|
| acknowledged by viewing the system trouble. |
|
|
|
|
|
|
|
| 2 Beeps | 1 | Bell/Siren line Cut | There is a problem with the Bell or Siren wiring. EOL2.2K resistor must be installed. |
|
|
|
|
|
|
|
|
| 3 | Rcvr | The receiver is not responding to the panel. The red LED on the receiver should be flashing, refer to WI848. The cover is off |
|
|
|
| Tamper | the receiver causing a tamper signal to be transmitted. |
|
|
|
|
|
| |
|
|
|
|
|
|
|
| 4 | Receiver Jam | A signal is blocking the normal reception of transmissions from the wireless devices. Ensure that the green LED on the |
|
|
|
|
| receiver is not on continuously, refer to receiver manual WI848. |
|
|
|
|
|
|
|
| 3 Beeps | Wireless | The battery in the wireless transmitter is low and should be replaced. This transmitter is on the zone corresponding to the |
| |
|
|
| Transmitter Low Battery | number of the zone light flashing. The replacement battery for the GEM Trans2 door/window transmitter and the GEM PIR |
|
|
|
| wireless motion detector is the Duracell DL123A. (2 required for the |
| |
|
|
|
| same type as specified above. Use of another battery may present a risk of fire or explosion. Do not recharge or disassemble |
|
|
|
|
| battery or dispose of in fire. |
|
| 4 Beeps | Wireless | The panel has not received a supervisory signal from the transmitter within the time programmed. Check Wireless |
| |
|
|
| Transmitter | Supervisory Timer [16] Programming. Check the placement of the transmitter and receiver, refer to WI848. |
|
|
|
|
|
| |
|
|
| Supervisory Failure |
|
|
|
|
|
|
|
|
| 7 Beeps | Zone Trouble | The panel has one or more of the following 3 possible troubles: Zone Short, Transmitter Tamper or Dual Tech Self Test Fail. |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
24