System Troubles
Use the System Trouble chart on the following page to determine the specific System Trouble
(s).
During normal panel operation the HSYSTEM LED has the following two modes of operation:
STEADY
FLASHING
Viewing System Trouble(s)
Press the I key on the keypad. To determine the System Trouble Group Number, count the number of times the HSYSTEM LED blinks.
The keypad sounder will beep at the same rate that the HSYSTEM LED blinks.
To determine the System Trouble, note the zone LED that is ON. Look up the specific system trouble on the chart on the following page.
The HSYSTEM LED and keypad sounder will
continue to flash and beep. To view the next System Trouble, if any, press the C key.
Continue pressing the C key, if there are no more system troubles to view, the system will
return to normal operation.
EXAMPLE - LOW BATTERY SYSTEM TROUBLE
Press the ito enter System Trouble mode and
determine the specific trouble. Press any key to view all system troubles.
| Flashing |
| System Trouble | |||
|
| |||||
| (System |
|
| Group # | ||
| Trouble |
|
|
|
| |
| Group |
| Keypad HSYSTEM | |||
| Number) |
| ||||
|
| Trouble LED is flashing 1 | ||||
|
| |||||
|
|
|
| time, | indicating | System |
|
|
|
| |||
|
|
|
| Trouble Group 1. |
| |
|
| Beeping |
| Keypad Sounder beeps 1 | ||
| (System |
| ||||
| Trouble |
| time | indicating | System | |
| Group |
| Trouble Group 1. |
| ||
|
|
|
|
| ||
| Number) |
|
|
|
| |
|
|
|
| |||
|
|
|
|
|
|
|
| Zone LED(s) is ON |
|
| Specific Trouble | |
| indicates |
|
| ||
|
|
|
| ||
| (Specific Trouble) |
|
| Zone 2 LED is ON indicating | |
|
|
|
|
| Low Battery. (1 Beep, LED 2) |
|
|
|
|
| |
|
|
|
|
|
|
FIGURE 8 SYSTEM TROUBLE EXAMPLE
Note: System Troubles Groups 3 through 7 - System Trouble Groups that have a zone or smoke detector associated with the trouble, such as RF low battery. The zone(s) of the device with a low battery will be displayed by the
ZONE LED. For example, a wireless low battery on zone 2 would beep the keypad sounder 3 times and turn on zone 2 LED.
Audible System Trouble Indication - For all system troubles, except when the only system trouble is the loss of AC, the keypad will beep once every 10 seconds. The keypad will continue to beep until the reset button is pressed or the trouble has been acknowledged by pressing the i key.
System Trouble Reporting
The following system troubles, when enabled to report to Telco 1
System Trouble | Pulse Report Code |
Bell Cut | F1 |
F1 | |
Rcvr | F1 |
Receiver Tamper | F1 |
Receiver JAM | F1 |
Tx Low Battery | F1 |
Tx Supervisory Failure | F1 |
If reporting using Point ID, a unique code will be sent for each of the following System Troubles.
System Trouble | Point ID Report Codes | |
Bell Cut | CODE 1 321 G00 | |
CODE 1 373 G00 | ||
Rcvr | CODE 1 382 G00 | |
Receiver Tamper | CODE 1 145 G00 | |
Receiver JAM | CODE 1 373 G00 |
A 300 (SYSTEM TROUBLE RST) code is sent if a restore is reported after multiple troubles.
23