Factory Default Settings, Factory default settings | NETGEAR C6300

AC1750 WiFi Cable Modem Router

Factory Default Settings

To return the modem router to its factory settings, press and hold the Reset button for over seven seconds. The modem router resets and returns to the factory configuration settings shown in the following table.

Table 2. Factory default settings

	Feature		Default Setting

	Modem router	User login URL	http://192.168.0.1
	login
	login	User name and password	admin / password
		User name and password	admin / password
		(case-sensitive)

	Local network	LAN IP	192.168.0.1
	(LAN)
	(LAN)	Subnet mask	255.255.255.0
		Subnet mask	255.255.255.0

		DHCP server	Enabled

		DHCP starting IP address	192.168.0.2

		DHCP ending IP address	192.168.0.254

	Firewall	Inbound communication from the	Disabled (except traffic on port 80, the HTTP port)
		Internet
		Outbound communication to the	Enabled (all)
		Internet

		Source MAC filtering	Disabled

	Internet	WAN MAC address	Use default hardware address
	connection

	Wireless	Wireless communication	Enabled

		SSID name	As shown on the product label

		Security	WPA/WPA2.. The default WPA/WPA2 passphrase is
			on the product label.
		Broadcast SSID	Enabled

		Transmission speed	Auto1
		Country/region	United States in the US; otherwise varies by region

		RF channel	Auto

		Operating mode	a, n, g, b, and ac

		Data rate	Best

		Output power	Full

		Access point	Enabled

Supplemental Information

97

Image 97

NETGEAR C6300 user manual Factory Default Settings, Factory default settings

Contents

AC1750 WiFi Cable Modem Router Compliance SupportTrademarks Contents Specify Network Settings Appendix a Supplemental Information Hardware Setup Front Panel Unpack Your Modem Router LED Position Your Modem Router Rear Panel  To retrieve the product label from the modem router Retrieve and Display the Product Label Cable the Modem Router in a Simple Network Cable Your Modem Router  To cable your modem router Cable Your Modem Router to a Router or Gateway To cable your modem router to a gateway or router Select Advanced Administration Router Mode Connect to the Network Access the Modem Router WiFi Connection Wired Connection To use WPS to connect to the WiFi network  To find and select the WiFi network Log In to the Modem Router Types of Logins To log in to the modem router Specify Initial Settings Notify Your Internet Provider  To set up your Internet connection  To change the starting frequency Specify the Cable Connection Starting FrequencySelect Cable Connection  To view the status of the modem router initialization View Modem Router Initialization  To specify the Internet connection settings Specify the Internet Connection SettingsSelect Advanced Setup Internet Setup Specify Initial Settings Control Access to the Internet  To set up Live Parental Controls Set Up Parental ControlsSelect Parental Controls Control Access to the Internet Click the Take me to the status screen button Use Keywords to Block Internet Sites To block Internet sites Click the Add Keyword button Select Advanced Security Block Sites To delete keywords from the list  To block services Block Services from the InternetSelect Advanced Security Block Services Schedule When to Block Internet Sites and Services  To schedule blocking Avoid Blocking on a Trusted ComputerSelect Advanced Security Schedule  To specify a trusted computer  To set up email notifications Set Up Security Event Email Notifications Control Access to the Internet Modem Router USB Drive Requirements Access a USB Drive on the Network To connect a USB drive  To specify the USB access settings Control Access to the USB Drive To map the USB device to a Windows network drive Network Neighborhood/MacShare. Enabled by default Select Advanced USB Storage Advanced Settings Use FTP Within the Network  To set up FTP access  To view or change network folders View or Change Network Folders on a USB Drive  To add a network folder Add a Network Folder on a USB DriveSelect Advanced ReadySHARE Click the Create Network Folder button Approve USB Devices Edit a Network Folder on a USB Drive To edit a network folder  To approve USB devices Click the Approved Devices button Select Advanced Advanced Setup USB SettingsSelect the Allow only approved devices check box Safely Remove a USB Drive Select USB Storage Basic Settings To remove a USB disk drive safely Specify Network Settings  To view or change the WAN settings View or Change the WAN SettingsSelect Advanced Setup WAN Setup  To change the MTU size Change the MTU Size Common MTU sizes  To set up a default DMZ server Set Up a Default DMZ Server Select Advanced Setup LAN Setup Change the LAN TCP/IP SettingsChange the Modem Router’s Device Name  To change the modem router’s device name  To change the LAN TCP/IP settings Specify the IP Addresses That the Modem Router Assigns  To reserve an IP address Reserve LAN IP Addresses  To delete a reserved address entry  To edit a reserved address entry Specify Basic WiFi Settings Use the WPS Wizard for WiFi Connections To use the WPS Wizard Select Advanced WPS Wizard  To specify basic wireless settings  To change the WPA settings Change the WiFi Security Option  To set up a guest network Set Up a WiFi Guest Network Select Guest Network Use the WiFi On/Off Button Control the Wireless RadiosEnable or Disable the Wireless Radios  To enable or disable the wireless radios Select Advanced Advanced Setup Wireless Settings Specify WPS Settings To specify WPS settings  To set up wireless card access Set Up a Wireless Card Access List Click the Set Up Access List button Select Advanced Advanced Setup Dynamic DNS  To set up Dynamic DNSSelect the Use a Dynamic DNS Service check box Dynamic DNS Select Advanced Advanced Setup UPnP  To enable Universal Plug and PlayImprove Network Connections with Universal Plug and Play  To refresh the information in the UPnP Portmap Table Manage Your Network View Cable Information View Modem Router Status To view modem router status and usage information  To view modem router cable information  To view modem router Internet port information View Internet Port Information Wireless Settings Reboot the Modem Router To view wireless settings  To reboot the modem router  To change the router mode Change the Router Mode  To view and customize logs View Logs of Modem Router Activity View a Network Map Select Advanced Administration Logs To view the network map Back Up Settings Manage the Modem Router Configuration FileSelect Advanced Administration Network Map  To back up the modem router’s configuration settings Erase the Current Configuration Settings Restore Configuration SettingsSelect Advanced Administration Backup Settings  To restore configuration settings that you backed up  To erase the configuration settings Change the admin Password To set the password for the user name admin Select Advanced Administration Set Password View Event Logs Select Advanced Administration Event LogRun the Ping Utility  To view the event logs  To run a ping test Run the Traceroute Utility Select Advanced Administration Diagnostics To run a traceroute test View or Change the Modem Router Wireless Channel View Wireless Access Points in Your Area To manage your wireless access point AP Select Advanced Administration Wireless AP Select Advanced Administration Wireless Channel  To view or change your wireless channelRemote Management  To set up remote management  To use remote access Specify Internet Port Settings  To forward specific incoming protocols Set Up Port Forwarding to a Local Server  To add a custom service Add a Custom Port Forwarding ServiceClick the Add Custom Service button Delete a Port Forwarding Entry Edit a Port Forwarding Service To edit a port forwarding entry  To delete a port forwarding entry Application Example Make a Local Web Server Public How the Modem Router Implements the Port Forwarding Rule To make a local web server public Add a Port Triggering Service Set Up Port Triggering To add a port triggering service Specify Internet Port Settings  To specify when to use port triggering Specify When to Use Port TriggeringClick the Apply button Application Example Port Triggering for Internet Relay Chat Troubleshooting Cannot Log In to the Modem Router Use LEDs to Troubleshoot Troubleshoot the Cable Internet Connection Troubleshoot a TCP/IP Network Using a Ping Utility Ping Use Ping to Test the LAN Path to Your Modem Router Reply from IP address bytes=32 time=NN ms TTL=xxx Supplemental Information Factory default settings Factory Default Settings AC1750 WiFi Cable Modem Router Factory default settings Technical Specifications