|
|
| Table | TIME MODE | ||
| KEY |
| DISPLAY |
| ACTION TAKEN | |
|
|
|
| SHOWS |
| AND PROCEDURE |
|
|
|
|
|
|
|
|
|
|
| xx:xx:xx |
| Displays current TIME setting |
|
| TIME |
|
|
| |
|
|
|
| 1. | Press the TIME key. The display flashes the TIME setting you | |
|
|
|
| |||
|
|
|
|
| selected just before starting the pump. | |
2.Use the UP and DOWN ARROW keys to enter the TIME setting you desire. As you use the UP and DOWN ARROW keys, the display changes accordingly. The SECONDS scroll,
|
|
|
|
|
|
| When you reach 0 or 59 seconds, the minutes setting changes. |
|
|
|
|
|
|
| When you reach 0 or 59 minutes , the HOURS setting |
|
|
|
|
|
|
| changes. Refer to Figure |
|
|
|
|
|
|
| NOTE: While the pump is running, you can not use the TIME key to |
|
|
|
|
|
|
| toggle from SECONDS to MINUTES TO HOURS. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| xxx mL/min | Displays actual FLOW RATE |
| FLOW |
|
|
|
| ||
| RATE |
|
|
| or |
| |
|
|
|
|
|
| Press the FLOW RATE key. The display flashes the calculated fluid | |
|
|
|
|
| |||
|
|
|
|
|
| xxx L/min | |
|
|
|
|
|
| flow rate (xxx mL/min or xxx L/min). | |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| xxx mL | Displays cumulative TOTAL VOLUME since start |
|
|
| TOTAL |
| |||
|
|
|
|
| or |
| |
|
|
| VOLUME |
|
| Press the TOTAL VOLUME key. The display flashes the calculated | |
|
|
|
|
|
| xxx Liters | |
|
|
|
|
| |||
|
|
|
|
|
|
| volume of fluid dispensed since the pump started running (xxx mL |
|
|
|
|
|
|
| or xxx Liters). |
|
|
|
|
|
|
|
|
|
|
|
|
|
| TUBE ID=xxx | Displays current TUBE ID |
| TUBE ID |
|
|
|
| ||
|
|
|
|
|
| ||
|
|
|
|
|
|
| Press the TUBE ID key. If the red LED next to the CALIBRATE key |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| is not lit, the display flashes the current TUBE ID setting. If the red |
|
|
|
|
|
|
| LED next to the CALIBRATE key is lit, the display flashes the |
|
|
|
|
|
|
| message “CALIBRATED TUBE!”. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| CALIBRATED! | Displays calibration state |
|
|
| CALIBRATE |
|
| ||
|
|
|
| or |
| ||
|
|
|
|
|
| 1. Press the CALIBRATE key. If the red LED next to the | |
|
|
|
|
|
| not calibrated | |
|
|
|
|
|
| CALIBRATE key is not lit, the display shows “not calibrated”. | |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| If the red LED next to the CALIBRATE key is lit, the display |
|
|
|
|
|
|
| shows “CALIBRATED!”. |
|
|
|
|
|
|
| To calibrate a tube: |
2.Press the START/STOP key to stop the pump. The display returns to the STOPPED Display Mode. For detailed instruc- tions on “Calibrating a Tube”, refer to Section 5.5.
and | xx:xx:xx | NOTE: if you press the UP and DOWN ARROW keys, the display | |
shows the current TIME setting. This setting changes | |||
|
| ||
|
| accordingly as you use the UP and DOWN ARROW keys. | |
|
|
| |
Language |
| NOTE: if you press the Language button, the display changes to | |
| the next language in the sequence: English, French, | ||
Button |
| ||
| Spanish, German, and Italian. | ||
|
| ||
|
| You will not notice this change unless the display | |
|
| shows something other than time. It is easier to change | |
|
| languages when you watch the display change. |
