■Audio TV Out (Sub)
`Off
`On
This preference determines whether the incoming audio signal is output from HDMI OUT SUB. You may want to turn this preference on if your TV is connected to HDMI OUT SUB and you want to listen to the audio from a connected component through your TV’s speakers. Normally, this should be set to “Off”.
Note
•If “On” is selected and the audio can be output from the TV, the AV receiver will output no sound through its speakers. In this case, “TV Speaker” appears on the AV receiver’s display by pressing DISPLAY.
•This setting is fixed to “Off” when “Monitor Out” is set to “Main” (➔ page 57).
•When “Monitor Out” is set to “Both” (➔ page 57), and this setting is enabled, set audio output of source component to 2ch PCM.
•With some TVs and input signals, no sound may be output even when this setting is set to “On”.
•When “Audio TV Out (Sub)” is set to “On” and you’re listening through your TV’s speakers, turning up the AV receiver’s volume control will make the sound be output from the AV receiver’s front left and right speakers. To stop the AV receiver’s speakers producing sound, change the settings, change your TV’s settings, or turn down the AV receiver’s volume.
•Listening mode cannot be changed when this setting is set to “On” and the audio is output from the TV.
•When “Monitor Out” is set to “Both” (➔ page 57) and only “Audio TV Out (Sub)” is set to “On”, the audio is not output from the TV connected to HDMI OUT SUB except in the case the audio input is via HDMI.
•If the audio signal from the player is not supported by the TV, the audio is not output from the TV even if this setting is enabled. When the audio cannot be output from the TV, (When “Monitor Out” is set to “Both”, the audio cannot be output form the TV connected to both HDMI OUT MAIN and HDMI OUT SUB) the audio is output from the speakers connected to the AV receiver.
■Audio Return Channel
`Off
`Auto:
The audio signal from your TV tuner can be sent to HDMI OUT MAIN of the AV receiver.
The audio return channel (ARC) function allows an ARC capable TV to send the audio stream to HDMI OUT MAIN of the AV receiver. To use this function, you must select the TV/CD input selector and your TV must be ARC capable. The ARC indicator will light when the audio signal is detected. Default setting:
“- - -
Note
•This setting is fixed to “- - -
•This setting is set to “Auto” automatically when the “HDMI CEC (RIHD)” setting is set to “On” for the first time.
•If you set “Audio Return Channel” to “Auto”, the “Audio Selector” settings of the TV/CD input selector will be automatically switched to “ARC” (➔ page 67).
Tip
•After changing the settings of the “HDMI CEC (RIHD)”,
“HDMI Through” or “Audio Return Channel”, turn off the power on all connected pieces of equipment and then turn them on again. Refer to the user’s manuals for all connected pieces of equipment.
■Lip Sync
`Off
`On
This function allows the AV receiver to automatically correct any delay between the video and the audio, based on the data from the connected monitor.
Note
•This function works only if your
Advanced Operations
■InstaPrevue
These settings apply to “InstaPrevue” of the Home menu (➔ page 51) and specify the preview display of HDMI video streams.
Sub Window
`Multi:
Displays preview thumbnails all at once.
`Single:
Displays preview thumbnails
Position
(with “Sub Window” set to “Multi”)
`Top, Bottom, Left, Right
(with “Sub Window” set to “Single”)
`Upper Left, Upper Right, Lower Left, Lower
Right
With this setting, you can set the position of preview thumbnails on the TV screen.
Note
•Depending on video signals, the picture may not be properly rendered on the preview thumbnails of InstaPrevue.
Auto Standby
■Auto Standby
`Off
`On
When “Auto Standby” is set to “On”, the ASb indicator lights and the AV receiver will automatically enter standby mode if there is no operation for 30 minutes with no audio and no video signal input. “Auto Standby” will appear on the AV receiver’s display and OSD 30 seconds before the Auto Standby comes on.
En-71
Operating procedure (➔ page 56)
