Onkyo TXNR727 instruction manual En-60, Speaker Distance

■Subwoofer

`Yes

`No

■Front

`Full Band

`40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,

200Hz

Note

•If the “Subwoofer” setting is set to “No”, the “Front” setting is fixed at “Full Band”.

■Center*1, Surround*1

`Full Band

`40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,

200Hz

`None

■Front High*1*2*3*5

`Full Band

`40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,

200Hz

`None

■Surround Back*1*2*3*4

`Full Band

`40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,

200Hz

`None

Note

*1 “Full Band” can be selected only when “Full Band” is selected in the “Front” setting.

*2 If the “Surround” setting is set to “None”, this setting cannot be selected.

*3 If the “Speakers Type (Front)” setting is set to “Bi-Amp”, or the “Powered Zone 2” setting is set to “Yes” together with Zone 2 turned on, this setting cannot be selected.

*4 If anything else than “None” is selected in “Front High”, this setting is automatically set to “None”.

*5 If anything else than “None” is selected in “Surround Back”, this setting is automatically set to “None”.

■Surround Back Ch

`1ch:

Select if only one surround back speaker L is connected.

`2ch:

Select if two (left and right) surround back speakers are connected.

Note

•If the “Surround Back” setting is set to “None”, this setting cannot be selected.

■LPF of LFE

(Low-Pass Filter for the LFE Channel)

`80Hz, 90Hz, 100Hz, 120Hz

`Off:

Low-Pass Filter is not applied.

With this setting, you can specify the cutoff frequency of the LFE channel’s low-pass filter (LPF), which can be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel.

Note

• If you’re using THX-certified speakers, select “80Hz”.

■Double Bass

This setting is NOT set automatically by Audyssey MultEQ® Room Correction and Speaker Setup function (➔ page 24).

`On

`Off(THX)

Turn this setting on to boost bass output by feeding bass sounds from the front left, right, and center channels to the subwoofer. Default setting: “- - - -”

Advanced Operations

Note

•When the “Subwoofer” setting is set to “No” or the “Front” setting to anything other than “Full Band”, this setting is fixed to “- - -”.

•This setting is set to “On” automatically when the

“Subwoofer” and “Front” settings are set for the first time to “Yes” and “Full Band” respectively.

•If you’re using THX-certified speakers, select “Off(THX)”.

Speaker Distance

This setting is set automatically by

Audyssey MultEQ Room Correction and Speaker Setup function (➔ page 24).

Here you can specify the distance from each speaker to the listening position so that the sound from each speaker arrives at the listener’s ears as the sound designer intended.

■Unit `feet:

Distances can be set in feet. Range: 1.0ft to 30.0ft in 1.0 foot steps.

`meters:

Distances can be set in meters. Range: 0.30m to 9.00m in 0.30 meter steps.

(The default setting varies from country to country.)

■Left, Front High Left, Center, Front High Right, Right, Surround Right, Surround Back Right, Surround Back Left, Surround Left, Subwoofer

`Specify the distance from each speaker to your listening position.

Note

•Speakers that you set to “No” or “None” in

“Speaker Configuration” cannot be selected (➔ page 59).

•When the “Powered Zone 2” setting is set to “Yes” and Zone 2 is turned on, the surround back and front high speakers cannot be used.

En-60

Operating procedure (➔ page 56)