Onkyo TXNR727 instruction manual En-32, Playing a USB Device, Listening to TuneIn, Playback

3 During this period (about 2 minutes), you can operate the Bluetooth-enabled device to pair with the AV receiver.

Note

•When establishing a connection with the AV receiver, select the profile (A2DP, AVRCP) at the Bluetooth- enabled device. If the Bluetooth-enabled device does not support the AVRCP profile, you cannot perform playback or other operations with the AV receiver.

Tip

•For details on the Bluetooth connection, refer to the instruction manual of the Bluetooth-enabled device.

4 Once the AV receiver is detected and the model name of the AV receiver appears on the display of your Bluetooth-enabled device, select the model name.

When a Bluetooth connection is established successfully, BLUETOOTH indicator will light.

Tip

•The model name appeared on the display of your Bluetooth-enabled device is “Onkyo TX-NR727”.

5 If passkey* is required on the display of the

Bluetooth-enabled device, enter “0000”.

The AV receiver only supports numerical passkey up to 4 digits.

*Passkey may be called “Passcode”, “PIN code”, “PIN number” or “Password”.

6 Play back the desired music on the Bluetooth- enabled device.

The audio is output from the AV receiver.

Tip

•The AV receiver may not work as normal depending on the circumstance even though the AV receiver is placed within the 15 meters range. In such cases, get the Bluetooth- enabled device closer to the AV receiver and retry the operation.

•When disconnecting on your Bluetooth-enabled device, BLUETOOTH indicator on the AV receiver will go off.

•If there is no sound output even after the pairing is done successfully, consult the instruction manual of the Bluetooth-enabled device, and then select the model name of the AV receiver as the audio output device.

•While connected to a Bluetooth-enabled device, the AV receiver cannot be detected and a connection cannot be established from another Bluetooth-enabled device.

•If you cannot connect with a paired Bluetooth-enabled device, perform the pairing operation between the AV receiver and the Bluetooth-enabled device again.

Note

•Due to the characteristic of Bluetooth wireless technology, the sound played on the AV receiver may slightly delay from the sound played on the Bluetooth-enabled device.

Playing a USB Device

Tip

•The on-screen information appears only on a TV that is connected to HDMI outputs.

This section explains how to play music files from a USB device (e.g., USB flash drives and MP3 players). See also:

• “Network/USB Features” (➔ page 94).

1	Press USB to select the “USB” input.
2	Plug your USB device into the AV receiver’s
	USB port.
	The USB indicator lights. It will flash if the AV
	receiver cannot read the USB device.
3	Press ENTER.
	A list of the device’s contents appears. To open a
	folder, use q/wto select it, and then press
	ENTER.
4	Use q/wto select a music file, and press
	ENTER or 1to start playback.
	En-32

Playback

Note

•While the message “Connecting...” appears on the AV receiver’s display, do not disconnect the USB cable supplied with the USB device from the USB port.

Listening to TuneIn

You need to connect the AV receiver to your home network (➔ pages 16, 27).

Tip

•The on-screen information appears only on a TV that is connected to HDMI outputs.

TuneIn is a new radio service which offers the music, sports and news all over the world.

Over 70,000 radio stations and 2 million on-demand programs are registered, and you can easily enjoy them by selecting stations or programs of your choice. TuneIn is preprogrammed on the AV receiver.

1 Press NET.

The network service screen appears, and the NET indicator lights. If it flashes, the AV receiver is not connected to the network correctly. If wired LAN connection is selected, verify that the Ethernet cable is firmly connected to the AV receiver. If wireless LAN connection is selected, verify that the Wi-Fiindicator lights.

Tip

•The same operation can be done by selecting “Network Service” in the Home menu.

2 Use q/w/e/rto select “TuneIn” and then press ENTER.