En-84, Video, Tuner, Remote Controller

■The beginning of audio received by an HDMI IN can’t be heard

Since it takes longer to identify the format of an HDMI signal than it does for other digital audio signals, audio output may not start immediately.

■There’s no sound during Whole House Mode

Make sure you’ve selected an analog audio input.

Video

■There’s no picture

Make sure that all video connecting plugs are pushed in all the way. (➔ page 18)

Make sure that each video component is properly connected. (➔ page 15)

If your TV is connected to the HDMI output(s), select “- - - - -” in the “HDMI Input” setting to watch composite video, and component video sources. (➔ page 58)

If the video source is connected to a component video input, you must assign that input to an input selector, and your TV must be connected to either the HDMI output(s) or COMPONENT VIDEO OUT. (➔ pages 15, 58)

If the video source is connected to a composite video input, your TV must be connected to the HDMI output(s) or the corresponding composite video output. (➔ page 15)

If the video source is connected to an HDMI input, you must assign that input to an input selector, and your TV must be connected to the HDMI output(s). (➔ pages 15, 58)

(European, Australian and Asian models) While the Pure Audio listening mode is selected, the analog video circuitry is turned off and only video signals input through HDMI IN can be output. (➔ page 41)

On your TV, make sure that the video input to which the AV receiver is connected is selected.

When the “Monitor Out” setting is set to “Both”, the “HDMI Through” setting is only available for the HDMI OUT MAIN jack. (➔ pages 57, 70)

■There’s no picture from a source connected to an HDMI IN

Reliable operation with an HDMI-to-DVI adapter is not guaranteed. In addition, video signals from a PC are not guaranteed. (➔ page 93)

When the resolution is set to any resolution not supported by the TV, no video is output from the HDMI outputs.

(➔ page 57)

If the message “Resolution Error” appears on the AV receiver’s display, this indicates that your TV does not support the current video resolution and you need to select another resolution on your DVD player.

■The on-screen menus don’t appear

On your TV, make sure that the video input to which the AV receiver is connected is selected.

When the AV receiver is not connected to a TV via HDMI OUT MAIN, on-screen menus are not displayed.

■The on-screen information does not appear

Depending on the input signal, the on-screen information may not appear when the input signal from HDMI IN is output to a device connected to the HDMI output.

Tuner

■Reception is noisy, FM stereo reception is noisy, or the FM STEREO indicator doesn’t light

Relocate your antenna.

Move the AV receiver away from your TV or computer.

Listen to the station in mono. (➔ page 38)

When listening to an AM station, operating the remote controller may cause noise.

Passing cars and airplanes can cause interference. Concrete walls weaken radio signals.

If nothing improves the reception, install an outdoor antenna.

En-84

Appendix

Remote Controller

■The remote controller doesn’t work

Before operating this unit, be sure to press RECEIVER.

Make sure that the batteries are installed with the correct polarity. (➔ page 11)

Install new batteries. Don’t mix different types of batteries, or old and new batteries. (➔ page 11)

Make sure that the remote controller is not too far away from the AV receiver, and that there’s no obstruction between the remote controller and the AV receiver’s remote control sensor. (➔ page 11)

Make sure that the AV receiver is not subjected to direct sunshine or inverter-type fluorescent lights. Relocate if necessary.

If the AV receiver is installed in a rack or cabinet with colored-glass doors, the remote controller may not work reliably when the doors are closed.

Make sure you’ve selected the correct remote controller mode. (➔ pages 11, 78)

When using the remote controller to control other manufacturers’ AV components, some buttons may not work as expected.

Make sure you’ve entered the correct remote control code. (➔ page 76)

Make sure to set the same ID on both the AV receiver and remote controller. (➔ page 73)

■Can’t control other components

If it’s an Onkyo component, make sure that the ucable and analog audio cable are connected properly. Connecting only an ucable won’t be enough.

(➔ page 20)