Adding Channels To a Scan List | Orion LBI-38888K specs

Adding Channels To A Scan List

1.With scan operation turned OFF select the desired channel to add to the selected conventional system channel scan list.

2.Press <or >on the SCAN add/delete control. The current status will be displayed in column 1 of line one for a time-out period. Press

<to add the channel to the scan list. S is displayed on the line. This sets the selected channel for non-priority scanning. A second press of

<sets the channel for priority-two scanning and 2 is displayed on line

one. An additional press of < sets the channel for priority-one scanning and 1 is displayed on line one. If the priority-one or priority- two channels are already set and a new channel is then assigned as the priority-one or priority-two channel, the previously assigned priority channel will change to non-priority scanning. The priority setting selection sequence is set and stops at priority-one therefore the channel

must be deleted from the scan list by pressing >before the channel is set to a previous priority setting. Any channel that is in a system's channel scan list will show S, 2 or 1 for the time-out period when it is the selected channel.

Deleting Channels From A Scan List

1.With scan operation turned OFF select the desired channel to delete from the selected conventional system's channel scan list.

2.Press <or >on the SCAN add/delete control. The current status is displayed for a time-out period. Press >to delete the channel from the scan list. S, 2 or 1 turns OFF. Any channel that is not in a conventional system channel scan list will show a "blank" for the time-out period when it is the selected channel.

Nuisance Delete

A channel can also be deleted from the scan list, if it is not the currently

selected channel, by pressing >during scan operation while the radio is displaying the unwanted channel. The channel will be deleted from the conventional system's channel scan list in the same manner as if done using the steps above. Deletions done in this manner will not remain deleted if the radio is turned OFF and then back ON.

58

Image 58

Orion LBI-38888K manual Adding Channels To a Scan List, Deleting Channels From a Scan List

Contents

Orion Product Specification for CE Marked Equipment Table of Contents Table of Contents Interference To Vehicular Electronic Systems Safety InformationList of the possible hazards are Explosive Atmospheres Dynamite Blasting Caps Introduction User Interface Orion Mobile Radio System Model Front Panel Controls Power ON-OFF Volume KnobSYSTEM/GROUP Channel Knob Scan ON/OFF IndicatorsRamp Control Scan ADD/DELETE Keypad Orion System Model Keypad Optional Keycap Configuration Standard Keycap ConfigurationKey Descriptions Entry see Selection Mode Rules Primary Functions Quick Access ALM Display Radio Status Icons Messages Message Name Description TX Data WHC=1 FIX List Spkr on System Busy Trunked Mode only Autokey Trunked Mode onlyCall Queued Trunked Mode only Alert Tones Dual Control Switching Call Denied Trunked Mode onlyCarrier Control Timer Operation Selection Mode Rules Turning on the Radio Direct Access U T H Menu N U K L G H T Press SEL Menu Item Information Feature Display Parameter Comment Settings SYS Scan Feature Encryption Data Stream Feature Encryption DisplaySerial Number ROM 12 Hex Digits Example Features Enabled Number Fields BIT Fields Possible Features SYSTEM/GROUP/CHANNEL Selection System Selection Group And Channel Selection Receiving a Call Trunked Mode OperationSending a Call Emergency Operation Conventional FailsoftReceiving An Emergency Call Declaring An Emergency Call System Scan OperationWide Area System Scan ProSoundTM ProScanTM Priority System Scan When Wide Area System Scan Is EnabledWhen ProSound/ProScan Is Enabled Menu Selection Group Scan Operation Adding Groups To a Scan List Deleting Groups From a Scan List Turning Scan on Nuisance DeletePriority Group Scanning Turning Scan OFF Individual CallsReceiving and Responding To An Individual Call Page Scat Operation Sending An Individual Call Sending a Telephone Interconnect Call Trunked Mode Only Receiving a Telephone Interconnect Call Trunked Mode OnlyTelephone Interconnect Calls Dtmf Overdial/Conventional Mode Telephone Interconnect Programmable Entries Mobile Data Displays Data OFF Operation Data On Operation Scan Lockout Mode Exiting Data Calls Data Lockout Mode STATUS/MESSAGE Operation Status Operation Edacs Conventional P1 Scan Message Operation Dynamic Regroup Operation Conventional Mode OperationEmergency Operation Receiving a Call Using 5-Tone Signalling for Emergency Declaration Tone Encode Transmission Scanning Conventional Channels Adding Channels To a Scan List Deleting Channels From a Scan List Turning Scan on Turning Scan OFF Squelch Adjust Noise Blanker Operation Type 99 Decode Conventional Only Menu Selection Direct Mode Operation Conventional System Only SIREN/LIGHT Operation Trunked or Conventional Mode OperationVoice Modes Yes AEGIS/ProVoice Digital ModeClear Modes Error Messages ERR=xxxxPage Transferring Keys Into The Radio Displaying The Currently Used Cryptographic Key Number Private Operation Receiving An Encrypted Call Key ZeroTransmitting An Encrypted Call Scanned Group Calls Conventional Operation Outside Address Dual Control Operation Switching ControlControl Switching Modes Channel Guard Independent Mode Operation Slaved Mode OperationSiren And Light Control Changing Selected Radio Multiple Radio OperationDual Control Audio Shared Control Unit Display Modes Audio Summed First Come First Serve DisplayAudio Modes Audio First Come First Serve Macro KEY Operation Page Keypad Remapping Operating Rules and Regulations Glossary Controller Group Or Subfleet Group Scan Individual Call QueueingSite System Inter Talk-aroundTelephone Connect Operators Radio Setup Radio Type Frequency Band Operators Name Emergency Group Warranty Emergency Numbers Operating Tips