Slaved Mode Operation, Siren And Light Control | Orion LBI-38888K

Slaved Mode Operation

During Slaved mode operation either controller can operate the radio with no change in System and Group settings when control is switched. Both controllers display the current information. If a key is pressed at the idle controller, other than PTT, Eor siren and light keys as noted in following paragraphs, a low tone will sound and the display will temporarily show DUAL on line one of the idle controller.

When control is switched in a Slaved mode system, all of the radio settings and states will remain in effect that have been selected on the active controller.

Independent Mode Operation

During Independent operation, the radio system operates as if there are two radio units each controlled by a separate control unit. Each control unit maintains its own System and Group settings which are restored when control is switched.

The idle controller will display DUAL on line one to indicate that it is idle. If a key is pressed at the idle controller, other than PTT, E or siren and light keys as noted in following paragraphs, a low tone will sound at the idle controller.

When control is switched in Independent mode, the idle controller will restore its own System and Group settings instead of using the settings of the previously active controller. Any pending operations at the active controller, other than Eor siren and light operations, will be terminated.

Emergency Operation

Either control unit (active or idle controller) can declare an emergency, provided radio has been pre-programmed to enable emergency declaration. If the idle controller declares an emergency, control is switched to the idle controller and any current transmission from the previously active controller is terminated.

Siren And Light Control

Siren and light control is only available from the control unit that is pre- programmed for these functions. Typically, the control unit at the driver's location would be programmed. The control unit that has these functions programmed can activate them regardless of whether it is an active or an idle controller.

72

Image 72

Orion LBI-38888K manual Slaved Mode Operation, Independent Mode Operation, Siren And Light Control

Contents

Orion Product Specification for CE Marked Equipment Table of Contents Table of Contents Safety Information List of the possible hazards are Explosive AtmospheresInterference To Vehicular Electronic Systems Dynamite Blasting Caps Introduction User Interface Orion Mobile Radio System Model Front Panel Power ON-OFF Volume Knob ControlsSYSTEM/GROUP Channel Knob Indicators Ramp ControlScan ON/OFF Scan ADD/DELETE Keypad Orion System Model Keypad Standard Keycap Configuration Optional Keycap ConfigurationKey Descriptions Entry see Selection Mode Rules Primary Functions Quick Access ALM Display Radio Status Icons Messages Message Name Description TX Data WHC=1 FIX List Spkr on Autokey Trunked Mode only Call Queued Trunked Mode onlySystem Busy Trunked Mode only Alert Tones Call Denied Trunked Mode only Carrier Control TimerDual Control Switching Operation Selection Mode Rules Turning on the Radio Direct Access U T H Menu N U K L G H T Press SEL Menu Item Information Feature Display Parameter Comment Settings SYS Scan Feature Encryption Display Feature Encryption Data StreamSerial Number ROM 12 Hex Digits Example Features Enabled Number Fields BIT Fields Possible Features SYSTEM/GROUP/CHANNEL Selection System Selection Group And Channel Selection Trunked Mode Operation Receiving a CallSending a Call Conventional Failsoft Emergency OperationReceiving An Emergency Call System Scan Operation Declaring An Emergency CallWide Area System Scan ProSoundTM ProScanTM When Wide Area System Scan Is Enabled When ProSound/ProScan Is EnabledPriority System Scan Menu Selection Group Scan Operation Adding Groups To a Scan List Deleting Groups From a Scan List Nuisance Delete Turning Scan onPriority Group Scanning Individual Calls Turning Scan OFFReceiving and Responding To An Individual Call Page Scat Operation Sending An Individual Call Receiving a Telephone Interconnect Call Trunked Mode Only Sending a Telephone Interconnect Call Trunked Mode OnlyTelephone Interconnect Calls Dtmf Overdial/Conventional Mode Telephone Interconnect Programmable Entries Mobile Data Displays Data OFF Operation Data On Operation Scan Lockout Mode Exiting Data Calls Data Lockout Mode STATUS/MESSAGE Operation Status Operation Edacs Conventional P1 Scan Message Operation Conventional Mode Operation Dynamic Regroup OperationEmergency Operation Receiving a Call Using 5-Tone Signalling for Emergency Declaration Tone Encode Transmission Scanning Conventional Channels Adding Channels To a Scan List Deleting Channels From a Scan List Turning Scan on Turning Scan OFF Squelch Adjust Noise Blanker Operation Type 99 Decode Conventional Only Menu Selection Direct Mode Operation Conventional System Only Trunked or Conventional Mode Operation SIREN/LIGHT OperationVoice Modes AEGIS/ProVoice Digital Mode YesClear Modes Error Messages ERR=xxxxPage Transferring Keys Into The Radio Displaying The Currently Used Cryptographic Key Number Key Zero Private Operation Receiving An Encrypted CallTransmitting An Encrypted Call Scanned Group Calls Conventional Operation Outside Address Switching Control Control Switching ModesDual Control Operation Channel Guard Slaved Mode Operation Independent Mode OperationSiren And Light Control Multiple Radio Operation Dual Control AudioChanging Selected Radio Shared Control Unit Display Modes First Come First Serve Display Audio ModesAudio Summed Audio First Come First Serve Macro KEY Operation Page Keypad Remapping Operating Rules and Regulations Glossary Group Or Subfleet Group Scan Individual Call Queueing SiteController System Talk-around TelephoneInter Connect Operators Radio Setup Radio Type Frequency Band Operators Name Emergency Group Warranty Emergency Numbers Operating Tips