Panasonic AG-HPG20, AG-HPG20E, AG-HPG20P Warning system table

Warning system table

When trouble is detected immediately after the power is turned on or during operation, the user is alerted by the power display LED and beep sound (provided that “ON” is selected for the “BEEP SOUND” setting on the setting menu “OTHER FUNCTIONS” (Page 106)).

Priority	Type of	LCD monitor screen			Power display	Beep sound	Warning description and	Action to be taken
Priority	warning	display			LED	Beep sound	record/playback operation	Action to be taken
		SYSTEM ERROR			Blinks at a	Beeps	P2 microprocessor or	Check the cause
1	System error	Cause displayed∗1,			rate of 4 times	Beeps	control trouble. Operation	display∗1, and consult
		blinks in red.			per second.	continuously.	is stopped.	your vendor.
		blinks in red.			per second.		is stopped.	your vendor.
							Trouble has occurred in the	Turn off the power.
							internal memory because a	Turn off the power.
	P2 card				Blinks at a		internal memory because a	If something is wrong
	P2 card	TURN POWER OFF			Blinks at a	Beeps	P2 card was ejected while	If something is wrong
2	ejection	TURN POWER OFF			rate of 4 times	Beeps	P2 card was ejected while	with the clips on the
2	ejection	Blinks in red.			rate of 4 times	continuously.	its data was being accessed.	with the clips on the
	trouble				per second.		Both access LEDs blink in	ejected P2 card, repair
							Both access LEDs blink in	them.
							orange (4 Hz).	them.
							orange (4 Hz).
		LOW BATTERY
		Blinks in red. Blinks with					The battery charge is low.
	Low battery	the remaining battery			Blinks at a	Beeps	Recording or playback
3	Low battery	display empty. (This			rate of once	Beeps	stops. If the voltage falls	Replace the battery.
3	charge	display empty. (This			rate of once	continuously.	stops. If the voltage falls	Replace the battery.
	charge	display appears even			per second.	continuously.	further, the power is
		display appears even			per second.		further, the power is
		when it has been set to					automatically turned off.
		OFF on the setting menu.)
		P2 FULL			Blinks at	Beeps
		P2 FULL			a rate of 4	Beeps	There is no more free
		Blinks in red (display			a rate of 4	continuously	There is no more free	Delete the unnecessary
		Blinks in red (display			times per	continuously	memory left on the P2	Delete the unnecessary
4	P2 card full	appears only for 3			times per	upon	memory left on the P2	clips or insert a new
4	P2 card full	appears only for 3			second upon	upon	card. Recording is	clips or insert a new
		seconds when [REC] is			completion of	completion of	stopped∗3.	card.
		pressed).			recording.	recording.
					recording.
						Beeps		Turn off the power and turn
						Beeps		it back on. Then check
		REC WARNING			Blinks at a	intermittently		it back on. Then check
	Recording	REC WARNING			Blinks at a	intermittently	Recording trouble.	the recording/playback.
5	Recording	Cause displayed	∗2	,	rate of 4 times	at a rate of	Recording trouble.	the recording/playback.
5	trouble	Cause displayed		,	rate of 4 times	at a rate of	Recording is stopped∗4.	Replace the P2 card
		blinks in red.			per second.	4 times per		if recording cannot be
						second.		if recording cannot be
						second.		performed properly.
								performed properly.
		One block on the
		remaining battery
	Near low	display is blinking. (This			Blinks at a		The battery charge is	Replace the battery as
6	battery	display appears even			rate of once	None	falling to low. Operation is	Replace the battery as
6	battery	display appears even			rate of once	None	falling to low. Operation is	necessary.
	charge	when it has been set			per second.		continued.	necessary.
	charge	when it has been set			per second.		continued.
		to OFF on the setting
		menu.)
							Under 2 minutes of
					Blinks at a		memory remaining on
					Blinks at a		the P2 card (remaining	Replace the P2 card
	P2 card	Remaining media			rate of once a		the P2 card (remaining	Replace the P2 card
7	P2 card	Remaining media			rate of once a	None	memory display shows	or add another card as
7	nearly full	memory display blinks.			second during	None	memory display shows	or add another card as
	nearly full	memory display blinks.			second during		less than one minute).	necessary.
					recording.		less than one minute).	necessary.
					recording.		This warning appears only
							This warning appears only
							during recording.
	Input image					Beeps	Recording stops due to
	Input image				Blinks at a	Beeps	the input signal distortion.
	frame				Blinks at a	intermittently	the input signal distortion.
	frame				rate of once a	intermittently	The recording will
8	distorted	IRREGULAR FRM SIG			second during	at a rate of	automatically resume	Check the input signals.
	during				recording.	2 times per	when input signals are
	recording				recording.	second.	when input signals are
	recording					second.	stabilized.
							stabilized.

∗1 P2 SYSTEM ERROR Cause display

•P2 MICON ERROR: P2 microprocessor does not respond.

•P2 CONTROL ERROR: Trouble has occurred in the P2 recording control.

•REC RAM OVERFLOW: Recording RAM overflow

∗2 REC WARNING Cause display

•CARD ERROR∗: P2 card trouble (slot number of trouble card is displayed in ∗)

•REC RAM OVERFLOW: Recording RAM overflow

•ERROR: Other recording trouble

∗3 The warning is cleared when any one of the following operations is performed.

•When a playback function button (STOP, PLAY, STILL, FF or REW) is pressed

•When the PC mode is selected while [THUMBNAIL/MODE] is held down for more than 2 seconds

•When a P2 card has been ejected or another card has been inserted

∗4 The warning is cleared when any one of the following operations is performed.

•When a playback function button (STOP, PLAY, STILL, FF or REW) is pressed

•When a P2 card has been ejected

Menu


For your	reference

109