Panasonic AJ-SD965 manual Interface

Setup menus (continued)

USER menu		<INTERFACE>
No./Item			Description
200	This selects whether two or more VTRs are
	to be operated in synchronization.
PARA RUN
		0000	DIS : No operation in synchronization
		0001	ENA : Operation in synchronization
	<Note>
	When operating two or more VTRs in
	synchronization, set all the VTRs to ENA.
201	This selects whether the 9P connector is to
	function when the REMOTE button is set to
9P SEL	the remote mode (REMOTE lamp ON).
		0000	OFF : Connector does not function.
		0001	ON : Connector functions.
202	This sets the ID information to be returned to
	the controller.
ID SEL
		0000	OTHER
		0001 DVCPRO
		0002	ORIG
	<Notes>
	OID information of any VTR except for the
		DVCPRO’s is set in OTHER.
	OThe ORIG setting should only be used when a
		Panasonic controller (AG-A850 etc. sold
		separately) is connected.
203	This selects whether the PARALLEL (25P)
	connector is to function when the REMOTE
25P SEL	button is set to the remote mode (REMOTE
	lamp ON).
		0000	OFF : Connector does not function.
		0001	ON : Connector functions.
204	This selects whether the RS-232C connector
	is to function when the REMOTE button is
RS232C SEL	set to the remote mode (REMOTE lamp ON).
		0000	OFF : Connector does not function.
		0001	ON : Connector functions.
205	These settings are for selecting the RS-232C
	communication speed (baud rate).
BAUD RATE
		0000	300
		0001	600
		0002	1200
		0003	2400
		0004	4800
		0005	9600
206	These settings are for selecting the RS-232C
	data length. (Unit: bit)
DATA LENGTH
		0000	7
		0001	8
207	These settings are for selecting the RS-232C
	stop bit length. (Unit: bit)
STOP BIT
		0000	1
		0001	2

No./Item		Description
208	These settings are for selecting the none,
	odd or even for the RS-232C parity bit.
PARITY
	0000	NON :
	Parity bit is not used.
	0001	ODD:
	An odd number of bits is used for the parity
	system.
	0002	EVEN:
	An even number of bits is used for the parity
	system.
209	These settings are for selecting whether the
	ACK code is to be returned when a command
RETURN ACK	is received from RS-232C.
	0000	OFF : ACK code is not returned.
	0001	ON : ACK code is returned.
210	For selecting the method used to detect the
	STANDBY COMMAND signal input at the
25P STBY CMD	PARALLEL (25P) connector.
	0000	OFF/ON :
	Each time active signals are detected, the
	STANDBY ON or STANDBY OFF mode is
	selected alternately.
	0001	ON :
	When active signals are detected in the
	STANDBY OFF mode, the unit is transferred
	to the STANDBY ON mode.
	Nothing happens if they are detected during
	an operation in the STANDBY ON mode.
211	This selects whether the PARALLEL (25P)
	connector is to function when the REMOTE
LOCAL 25P	button is set to the local mode (REMOTE
	lamp OFF).
	0000	OFF : Connector does not function.
	0001	ON : Connector functions.
212	For selecting the remote control connector to
	control the slave when the unit is used as the
MASTER PORT	master during deck-to-deck operations.
	0000	IN/OUT : The IN/OUT connector is used.
	0001	OUT : The OUT connector is used.
	<Note>
	This setting takes effect only when the REMOTE
	button is set to the local mode (REMOTE lamp
	OFF).

The underlined items indicates the initial setting.

45