Manuals / Panasonic / Household Appliance / Home Security System

Panasonic AW-RP50N Setting and operating the preset memories, 3Press the STORE button, Memo

Models: AW-RP50N

1 82

Download 82 pages 17 Kb

Page 5

Setting and operating the preset memories

Setting and operating the preset memories

This unit has a preset memory function for registering the preset data of the shooting positions and settings of the remote cameras.

Up to 100 sets of data (presets) can be registered in these memories.

Registering data in the preset memories

1Press one of the CAMERA STATUS/ SELECTION buttons 1 to 5 to select the remote camera to be operated.

2Output the images to be shot by the camera to the monitor.

The camera angle to be registered is determined by operating the PAN/TILT lever and ZOOM button.

If necessary, adjust the focus and iris as well.

3Press the STORE button.

4After pressing the PAGE button, press the PRESET MEMORY/MENU button to specify the page number to be registered.

In this step, the number of the page to be registered as the preset memory is specified.

5Hold down the PRESET MEMORY/MENU button of the number on the page.

In this case, specify the number on the page which was specified in step 4.

3	4			4, 5
		1	2	3	4	5
MENU	PAGE	GAIN/PED	R/B GAIN	R/B PED	AWB/ABB	SHUTTER	F2	EXIT
		6	7	8	9	10
STORE	DELETE	DETAIL	SCENE/MODE	CAMERA	SETUP	SYSTEM	USER1	USER2
			PRESET MEMORY / MENU
		1	2	3	4	5
IRIS	AUTO		CAMERA STATUS / SELECTION					PT ACTIVE
			CAMERA STATUS / SELECTION
				1

Note

When specifying the number on the page, it is registered by holding down the PRESET MEMORY/MENU button.

To register more data, repeat steps 2 to 5.

When specifying a different “number on the page” on the same “page number,” it is registered by skipping step 4 and carrying out the operation in step 5 only.

Preset numbers and registered pages

Preset No.	Page No.	Number on the page
1 to 10	1	1 to 10
11 to 20	2	1 to 10
21 to 30	3	1 to 10
31 to 40	4	1 to 10
41 to 50	5	1 to 10
51 to 60	6	1 to 10
61 to 70	7	1 to 10
71 to 80	8	1 to 10
81 to 90	9	1 to 10
91 to 100	10	1 to 10

Memo

Example: When specifying preset 21

Press the following buttons in the order given: PAGE button PRESET MEMORY/MENU 3 button PRESET MEMORY/MENU button 1.

5

Image 5

Panasonic AW-RP50N Setting and operating the preset memories, Registering data in the preset memories, Memo

Contents

Remote Camera Controller Operating InstructionsModel No. AW-RP50N Operations and SettingsHow to turn the power of the remote cameras on ContentsSelecting the settings for a selected remote Operating the menu items of the selected remoteBefore use Network-relatedprecautionsOverview Concerning the Operating Instructions2Set PRESET MEMORY/MENU 8 button CAMERA to ON How to turn the power of the remote cameras on1Select the remote camera 1Set the MENU button to ONRegistering data in the preset memories Setting and operating the preset memories3Press the STORE button MemoDeleting the preset memory data Executing the preset data1Press the DELETE button Setting and operating the preset memoriesSetting the pedestal Setting the gain3Turn the F1 dial to select the setting 3Turn the F2 dial to select the settingSetting the R and B pedestal Setting the R and B gain valuesRGAIN ±000 BGAIN ±000 RPEDSelecting the white balance mode Setting the white balanceAWB MODE AWB B 1Set the MENU button to ONAWB MODE AWB A Automatically adjusting the white balanceMemo 1Set the MENU button to ON1Set the MENU button to ON 3Set the MENU button to ON3Turn the F1 dial to select ATW Automatically adjusting the black balance Setting the black balanceManually adjusting the black balance 2Set the MENU button to ONSetting the detail Setting the shutter speed2Set the PRESET MEMORY/MENU 6 button DETAIL to ON 3Turn the F1 dial to select the shutter modeSpecifying the color bars Setting the shooting mode3Turn the F1 dial to select the shooting mode SCENE MANU1 MODE CAMRemote camera Table of operationsMenu ON/OFF Cursor movements2Set the PRESET MEMORY/MENU 9 button SETUP to ON Setting the USER buttonsRegistering functions in the USER buttons 3Press the F1 dial4Turn the F1 dial to select the target menu item Setting the functions4OPERATE 1.PAN DIRSetting the panning direction Setting the remote camera operationsSetting the tilting direction Setting the zooming direction6.SPEED TARGET R/T/Z/F 5.SPEED WITHZ OffP/T/Z/F Setting the functions7.FOCUS/IRIS NORMAL Setting the PAN/TILT lever inclination and speed8.P/T CURV Setting the functions2.SCOPE MODE A 1.DIAG SPEEDSetting the functions ModeSetting the lower limit Setting the upper limitDisplay that appears with the AW-HE50 3.LIMIT UP OffSetting the right limit Setting the left limit5.LIMIT LEFTOff 5.LIMIT LEFTOnSetting the functions 3.HOMEPOSITION SETControlling an ND filter 6FUNCTION1.ND FILTEROff Controlling an AC adapter AW-PS300AAdjusting the minimum lens zoom start speed Adjusting the minimum pan/tilt start speed1.P/T MIN SPEED START 2.Z MIN SPEEDSetting button operation enable or disable Setting the preset numbers1.MENU CONTROL ENABLE Locking the button operationsSwitcher network settings Linking the unit with the switcher2Set PRESET MEMORY/MENU 10 button SYSTEM to ON 1Set the MENU button to ON1CAMERA CTL Setting the image output and image input3SW ASSIGN 1.INPUT1 CAM12Set PRESET MEMORY/MENU 9 button SETUP to ON Switcher settingsLinking the unit with the switcher 1Set the MENU button to ONFocus assist setting Bus settingCamera information setting 3.BUS AUXPAN/TILT lever control setting OA tally setting6.TALLY IP Off 7.P/T LEVERLinking the unit with the switcher Setting all the information displays together2Set PRESET MEMORY/MENU 9 button SETUP to ON 1Set the MENU button to ONRemote camera alarm information Setting each information item to be displayed9.ALARM Off Video format8ALARM Checking the equipment alarm information1.POWER NO ALARM NO ALARM5Press the F2 dial to initialize the settings Set PRESET MEMORY/MENU 10 button SYSTEM to ON1.INITIALIZE SETUP SETUPSETTINGTALLY/GPI Control interface for external devicesD-sub 15-pin,female, inch thread Example of GPI Out connectionsInstalling the software RP setting toolIP settings Software provided on the CD-ROMChanging the IP addresses Auto IP settingChanging the camera numbers 1Click RENEWDisplaying the camera names Alarm displaysInitializing the IP addresses Acquiring informationSaving and loading data Saving the setting files2Input the filename, and click Save RP setting toolSaving the log files Loading the setting files1Click File 2Select the file, and click OpenSetting Table of menu itemsButton Menu itemTable of menu items SettingButton Menu itemTable of menu items SettingButton Menu itemTable of menu items SettingButton Menu itemF0410Y0 Model No. AW-RP50N Operating Instructions BasicsRemote Camera Controller THIS APPARATUS MUST BE EARTHED Safety precautionsindicates safety information IMPORTANT SAFETY INSTRUCTIONSSafety precautions Accessories Network-relatedprecautionsInstallation precautions Operating precautionsBefore use Network-relatedprecautionsOverview Concerning the Operating InstructionsCompact design CharacteristicsIP connection and serial connection supported IP connectionPan-tiltheads supported AccessoriesPan-tiltheads and cameras supported Required personal computer environment Connecting the power supply Installation precautionsChoosing the best installation location Handle carefullyWhen the product is to be discarded Operating precautionsHandle carefully Avoid humidity and dustALARM indicator ALARM POWER indicator POWERParts and their functions Control panelCAMERA OSD button CAMERA OSD PRESET MEMORY/MENU buttons PRESET MEMORY/MENUEXIT button EXIT USER buttons USER1, USER2Button indicator OFF Manual focusing Button indicator ON Auto focusingWhen it is turned clockwise Button indicator ON Auto irisGround terminal SIGNAL GND POWER switch POWERSERVICE switch SV/NM LAN connector LAN RJ-4510BaseT/100BaseTX4Adjust the zoom 1Turn on the unit’s power5Adjust the lens iris 6Adjust the focusSet the MENU button to ON Basic operations for the menusSelect the target menu Setting the unit Network settings6Turn the F2 dial, and select the setting 7Press the F2 dial, and change the settingSetting the subnet mask Setting the IP addressSetting the default gateway Setting the MAC addressExample of IP connections ConnectionsConnections with the AW-HE50and AW-HS50 SDI video signalConnection with the AW-HE50 Example of serial connectionsConnection with the AW-HE100 ConnectionsSwitch settings Connections with the AW-PH400and cameraConnections Zoom lensConnections Connections with the AW-PH405and cameraZoom lens 10BASE-TUTP category 5 straight cableConnections Connection with the AW-PH650RJ-45relay adapter 10BASE-TUTP category 5 straight cableSerial connection Settings for connection with the remote camerasIP connection 1.CAM1 SerialConnections When setting the IP addresses for the first time2 On the SYSTEM menu, select AUTO SET SET UP IP COMPLETE SET UP IP tttttSET UP IP SET UP ERR C 20/20 S 1/1 C/S OVER! YESConnections 1.AUTO SETUP KEEP2 On the SYSTEM menu, select AUTO SET MemoSET UP IP ttttt SET UP IP IP DuplicateERRSET UP IP COMPLETE SET UP IP SET UP ERRChanging the IP addresses of the remote cameras Setting the IP addressesSelecting the camera group 1.GROUP SELECTChanging the camera numbers Changing the IP address of the switcherClearing the IP address control tables 3Press the F2 dial to enter the IP addressSelecting the remote cameras to be operated 2Set the PRESET MEMORY/MENU 8 BUTTON CAMERA to ON1Set the MENU button to ON 3Press the F1 dialto cool down MaintenanceUnit mm inch Appearance189 7-7/16 210 8-1/4Input/Output connector SpecificationsPower requirements: DC 12 V 10 % Power consumption DC 12 V, 0.5 AF0410Y0