Panasonic DMR-EA38V warranty Error Messages, On the Unit’s Display

Error Messages

On the Unit’s Display			Page
H	, F	 An error has occurred. The number following “H” or “F” depends on the	−
(“ ” stands for a service number.)		status of the unit. Check the items below and in the Troubleshooting Guide.
		If the service number still does not disappear after the check, reset the unit
		( 74, “To restore the unit if it freezes”).
		 If the service numbers fail to clear, note the service numbers and contact a	−
		qualified service person.
RC	(“ ” stands for a number.)	 The remote control and the main unit are using different codes. Change the	53
		code on the remote control.
HARD ERR		 If there is no change after turning the unit on and off, consult the dealer	−
(“HArd” and “Err” are alternately		where the unit was purchased.
displayed.)
NO READ		 The disc is dirty or badly scratched. The unit cannot record, play, or edit.	67
(“NO” and “REAd” are alternately		 The disc may be incompatible or of poor quality.	66, 67,
displayed.)
			69
		 You have used a lens cleaner and it has finished operation. Press	13
		[ OPEN/CLOSE] on the main unit to eject the disc.
		 Displayed when the unit is started. This is not a malfunction.	−
		 The unit is carrying out its recovery process. You cannot operate the unit	−
		while “ ” is displayed.
FULL		 There are already 16 scheduled recording programs. Delete unnecessary	25
		scheduled recording programs.
UNSUPPORT		 You have inserted a disc the unit cannot play or record on.	66, 67
(“UNSUP” and “POrt” are alternately		 You tried to operate with a non-compatible USB memory.	68
displayed.)
UNFORMAT		 You have inserted a new DVD-RW/+RW or a DVD-RAM/DVD-RW	23, 48
(“UNFOr” and “MAt” are alternately		(DVD-Video format) recorded on other equipment.
displayed.)		You can format the disc when the format confirmation screen is displayed.
“	” is displayed on the unit’s	 This unit is confirming that it is connected with equipment compatible with	−
display.		HDAVI Control.
F74		 The HDMI connection could not be authenticated due to a transfer	−
		malfunction. Consult the dealer where the unit was purchased.
F75		 The HDMI connection could not be authenticated due to an internal data	−
		malfunction. Consult the dealer where the unit was purchased.
U59		 The unit is very warm.	−
		The unit switches to standby for safety reasons. Wait for about 30 minutes
		until the message disappears.
		Reinstall the unit in an area with adequate ventilation. Do not block the
		cooling fan on the rear of the unit.
U61		 There was a power failure or the AC power supply cord was disconnected	−
		while the unit was on. The unit is carrying out its recovery process. This
		process restores the unit to normal operation. The unit is not broken. Wait
		until the message disappears.
U72		The HDMI connection acts unusually.	−
U73		– The connected equipment is not HDMI compatible.
		– Please use HIGH SPEED HDMI cables that have the HDMI logo (as shown on the cover).
		– The HDMI cable is damaged.
U76		 HDMI cannot be output because you are connected to a model that does	−
		not support copyright protection.
U88		 There was something unusual detected with the disc while recording,	76
		playing or copying; there was a power failure or the AC power supply cord
		was disconnected while the unit was on. The unit is carrying out its recovery
		process. This process restores the unit to normal operation. The unit is not
		broken. Wait until the message disappears.
U99		 The unit fails to operate properly. Press [/I POWER] on the main unit to	−
		switch the unit to standby. Press [/I POWER] on the main unit again to
		turn the unit on.

72

RQT9058