Displayable character set | Panasonic KX-HCM270 guide

Operating Instructions

Displayable character set

Network Camera can display ISO-8859-1 character set for West European languages and the Shift-JIS character set for Japanese. Network Camera screen may display the unreadable characters if the operating system or the entered character set is different from the language selected on Top View Image Setting window.

ISO-8859-1 Character Table

¡	˚	À	Ð	à	ð
¡	±	Á	Ñ	á	ñ
¢	²	Â	Ò	â	ò
£	³	Ã	Ó	ã	ó
¤	´	Ä	Ô	ä	ô
¥	µ	Å	Õ	å	õ
¦	¶	Æ	Ö	æ	ö
§	·	Ç	×	ç	÷
¨	¸	È	Ø	è	ø
©	¹	É	Ù	é	ù
ª	º	Ê	Ú	ê	ú
«	»	Ë	Û	ë	û
¬	¼	Ì	Ü	ì	ü
-	½	Í	Ý	í	ý
®	¾	Î	Þ	î	þ
¯	¿	Ï	ß	ï	ÿ

[For assistance, please call: 1-800-272-7033]

109

Image 109

Panasonic KX-HCM270 operating instructions Displayable character set, For assistance, please call 109

Contents

Network Camera For operation assistance Call Introduction Network Camera Memo TrademarksFor assistance, please call Important Safety Instructions Table of Contents Technical Guides Specifications and Troubleshooting 111Index 133 Section Getting to Know Network Camera Main Features Update Firmware Multi-Client AccessAuthentication Multi-Camera Screen System Requirements Authentication window Authentication-System Security Feature Setup CD-ROM 1 pc Rubber Cap 1 pc Included AccessoriesSelf Bonding tape Connector Cover AC Adaptor 1 pc Flexible Stand 1 pc Sunshade 1 pc Setup CD-ROM Lens Cover Indicator Camera Feature LocationsFront View Fixed Focus Lens Bottom View Rear View Network Camera Setup Installation Procedure Network Camera can be installed on the LAN/Intranet Network Camera Configuration TypeType 2-Internet Connection with a Broadband Router Type 4-Direct Connection with a PC Type 3-Internet Direct Connection with a Modem How to turn on Network Camera for Installation Preparing the Network Parameters for Network Camera Network ParametersNetwork parameters memo for Network Camera Default Network Camera Configuration TypeNetwork Parameters Table Type Port No Click OK to close IP Configuration window How to refer the network parameters from the PC Setting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display To access Network window Wireless SetupTo set up the wireless network parameters Set Infrastructure Default or AdHoc Connection and Signal Strength statusChannel Encryption Key window Encryption Password window Wireless Settings Default Key If Top Page does not appear Port Forwarding IP Masquerade feature Network Camera Access from the Internet Top Network Camera Screen and Setup Window Network Camera Flow Chart Example TopHttp//Global IP address of Broadband RouterPortNo Top Single Camera Motion JpegMulti-Camera Help ActiveX Controls Single Camera Screen Click to Center Using Operation Bar Using Pan/Tilt Operation Setting Preset Positioning and Home Positioning Click Delete Deleting the preset buttons Viewing Buffered Image Screen Non Transfer mode Alarm/Timer mode Clicking Start Capture ViewerPrimary Secondary Multi-Camera Screen Setup Setup Go to Top AdministratorName/Time Security Reset to Factory Indicator ControlExternal Output Control Go to Top Network Enter only the number Instructions for the data fields Check Dhcp Dynamic Host Configuration Protocol If you use Network Camera on the LAN, set upHost Name When your ISP uses the Dhcp server function which Or administrator for the Host name File size of the image Camera Name/TimeName Date Time Changed AM/PM or 24H AdjustmentAuto Time Zone Refer to page 65 for details about authentication security Security AdministratorClick Security Administrator on Setup Administrator and General User Authentication window EnableFor Setup Password Retype Security General User Click Security General User on Setup Operating Instructions Top View Image Instructions for the data fields Top ResolutionImage 160 x Image Transfer Non Transfer mode Click Alarm on Image Transfer window Transfer in the Alarm Mode Active Time of Trigger Alarm enable condition Login timing Data transfer method Over write setting Setting Example Setting explanation Transfer in the Timer Mode Image Frequency Sets the interval to send the image Buffers or transfers by the timer trigger Login timing Over write setting Instructions for the data fields White Balance Camera SetupFixed Indoor Fixed Suggested White Balance is also registered in preset programmingHaving reached the selected end Tilt Range Specifying the Pan/Tilt range Click Save when finished Multi-Camera IP Address or Enable check boxURL * 1 or Host Camera Name External Output Control Click External Output Control on Setup Indicator Control Status Restart Click Cancel to quit. The window returns to SetupClick Restart Now Update Firmware Click Update Firmware Click Update Firmware on Setup Open Reset to Factory Default Technical Guides Outdoor Installation Network Camera Installation High performance for wireless communication Network Camera Cabling Be sure to thread the AC adaptor cord through the hook Inches Cover the putties by rollingDo not cover Ventilation hole 100 Network Camera Mounting Attach Network Camera to the tripod using the tripod boltFlexible Stand Mounting Tripod Mounting Stand if necessary Wall MountingWaterproof the rest of the cable Self Bonding tape 102 Caulk around Flexible Stand if necessary Ceiling MountingWaterproof the rest Cable For assistance, please call 103 Top Bottom Making holes on mortar wall Explanation of External I/O Interfacing to the External I/OPin Function External Sensor Input Circuit Diagram Example Unavailable character set Ascii and ISO-8859-1 Character TableSpace, , , #, &, %, =, +, ?, , and are not available 108 For assistance, please call 109 Displayable character set 110 Maintenance For assistance, please call 111 Specifications and Troubleshooting 112 Network Camera Reset Procedure-Default Settings For assistance, please call 113 Default Settings List 114 For assistance, please call 115 Items Factory Default Indispensable setting Value Alarm 116 Timer 117 Items Factory Default Indispensable setting Value Timer 118 Control Indicator Control Network Camera Specifications Description SpecificationsOther Specification Description Message Transferring Method Weight 570 1.26 lb. Only the unitMm 3.46 inches Excluding the antenna and protruding objects About Network Camera Setup TroubleshootingProblem Cause and Remedy When Top Page does not appear, port number 80 might not be Proxy server may prevent you from connecting directly toWhen you use DDNS, you need to set Default Gateway If Top Page does not appear in the above procedure, press Network window on For Indicator Control windowTransfers older Refer to page 91 for the Update Firmware About Network Camera Setup Problem Cause and Remedy124 Lens About Top View Image screen About Other Troubles View Image Setting window on Confirmation of Network Camera Operation Click the language to change the display FCC and Other Information Medical AdHoc GlossaryEncryption WEP Ieee 802.11b 132 133 Index Operating Instructions TCP/IP Wireless Router 37 Wireless window 136 137 When you ship the product For product service