Camera Feature Locations, Front View | Panasonic KX-HCM270 guide

Operating Instructions

1.3Camera Feature Locations

1.3.1Front View

Antenna

Lens Cover

Indicator

(Refer to page 88 for the setup.)

Fixed Focus Lens

1 m (40 inches)—Infinity

Pan: - 60° to + 60°

Tilt: 0° to - 45°

The field of view in Pan/Tilt ranges horizontally about 165° and vertically about 78°.

Indicator

Indicator can be controlled on Indicator Control window on page 88. Color indications are shown below.

Power	Not on the LAN	Orange		Orange blinking*1		Orange

on	On the LAN	Orange		Green blinking		Green

	Normal Operation			Green
Using	Getting IP address			Green blinking
DHCP	Finish getting IP address			Green
	Updating Firmware			Orange blinking
Pushing CLEAR SETTING button				Orange blinking twice
Internal Failure of Network Camera				Red blinking*2

*1 Orange indicator will continue blinking in the DHCP setting. *2 Refer to page 123 for the red blinking.

Fixed Focus Lens and Pan/Tilt operation

Fixed Focus Lens can move in the Pan/Tilt operation. Operation Bar on the Single Camera screen can operate the Pan/Tilt. The Pan/Tilt moves the lens 120° horizontally and 45° vertically. Refer to page 46 for the operation bar.

Note

Do not touch the Lens Cover. Touching it may leave a fingerprint and can cause the image to be out of focus.

14

Image 14

Panasonic KX-HCM270 operating instructions Camera Feature Locations, Front View, Lens Cover Indicator, Fixed Focus Lens

Contents

Network Camera Introduction For operation assistance Call For assistance, please call TrademarksNetwork Camera Memo Important Safety Instructions Table of Contents Index 133 Specifications and Troubleshooting 111Technical Guides Section Main Features Getting to Know Network Camera Authentication Multi-Client AccessUpdate Firmware Multi-Camera Screen System Requirements Authentication-System Security Feature Authentication window Self Bonding tape Connector Cover Included AccessoriesSetup CD-ROM 1 pc Rubber Cap 1 pc AC Adaptor 1 pc Flexible Stand 1 pc Sunshade 1 pc Setup CD-ROM Front View Camera Feature LocationsLens Cover Indicator Fixed Focus Lens Rear View Bottom View Network Camera Setup Installation Procedure Type 2-Internet Connection with a Broadband Router Network Camera Configuration TypeNetwork Camera can be installed on the LAN/Intranet Type 3-Internet Direct Connection with a Modem Type 4-Direct Connection with a PC How to turn on Network Camera for Installation Network parameters memo for Network Camera Network ParametersPreparing the Network Parameters for Network Camera Network Parameters Table Network Camera Configuration TypeDefault Type Port No How to refer the network parameters from the PC Click OK to close IP Configuration window Setting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display To set up the wireless network parameters Wireless SetupTo access Network window Channel Connection and Signal Strength statusSet Infrastructure Default or AdHoc Encryption Password window Encryption Key window Default Key Wireless Settings If Top Page does not appear Network Camera Access from the Internet Port Forwarding IP Masquerade feature Top Network Camera Screen and Setup Window Network Camera Flow Chart Http//Global IP address of Broadband RouterPortNo Top TopExample Multi-Camera Motion JpegSingle Camera Help ActiveX Controls Single Camera Screen Click to Center Using Operation Bar Using Pan/Tilt Operation Setting Preset Positioning and Home Positioning Deleting the preset buttons Click Delete Non Transfer mode Alarm/Timer mode Viewing Buffered Image Screen Primary ViewerClicking Start Capture Secondary Multi-Camera Screen Setup Setup Name/Time AdministratorGo to Top Security External Output Indicator ControlReset to Factory Control Go to Top Network Instructions for the data fields Enter only the number Host Name When your ISP uses the Dhcp server function which If you use Network Camera on the LAN, set upCheck Dhcp Dynamic Host Configuration Protocol Or administrator for the Host name File size of the image Name Name/TimeCamera Date Auto AdjustmentTime Changed AM/PM or 24H Time Zone Click Security Administrator on Setup Security AdministratorRefer to page 65 for details about authentication security For Setup Password EnableAdministrator and General User Authentication window Retype Click Security General User on Setup Security General User Operating Instructions Top View Image Image ResolutionInstructions for the data fields Top 160 x Image Transfer Non Transfer mode Transfer in the Alarm Mode Click Alarm on Image Transfer window Alarm enable condition Active Time of Trigger Login timing Over write setting Data transfer method Setting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Image Frequency Sets the interval to send the image Login timing Over write setting Fixed Indoor Camera SetupInstructions for the data fields White Balance Fixed Having reached the selected end White Balance is also registered in preset programmingSuggested Tilt Range Click Save when finished Specifying the Pan/Tilt range Multi-Camera URL * 1 or Host Enable check boxIP Address or Camera Name Click External Output Control on Setup External Output Control Indicator Control Status Click Restart Now Click Cancel to quit. The window returns to SetupRestart Update Firmware Click Update Firmware on Setup Click Update Firmware Open Reset to Factory Default Technical Guides Network Camera Installation Outdoor Installation High performance for wireless communication Network Camera Cabling Be sure to thread the AC adaptor cord through the hook Do not cover Ventilation hole 100 Cover the putties by rollingInches Flexible Stand Mounting Attach Network Camera to the tripod using the tripod boltNetwork Camera Mounting Tripod Mounting Waterproof the rest of the cable Self Bonding tape 102 Wall MountingStand if necessary Waterproof the rest Cable For assistance, please call 103 Ceiling MountingCaulk around Flexible Stand if necessary Top Bottom Making holes on mortar wall Pin Function Interfacing to the External I/OExplanation of External I/O External Sensor Input Circuit Diagram Example Space, , , #, &, %, =, +, ?, , and are not available Ascii and ISO-8859-1 Character TableUnavailable character set 108 Displayable character set For assistance, please call 109 Maintenance 110 Specifications and Troubleshooting For assistance, please call 111 Network Camera Reset Procedure-Default Settings 112 Default Settings List For assistance, please call 113 114 Items Factory Default Indispensable setting Value Alarm For assistance, please call 115 Timer 116 Items Factory Default Indispensable setting Value Timer 117 Control Indicator Control 118 Other Specification Description SpecificationsNetwork Camera Specifications Description Mm 3.46 inches Weight 570 1.26 lb. Only the unitMessage Transferring Method Excluding the antenna and protruding objects Problem Cause and Remedy TroubleshootingAbout Network Camera Setup When you use DDNS, you need to set Default Gateway Proxy server may prevent you from connecting directly toWhen Top Page does not appear, port number 80 might not be If Top Page does not appear in the above procedure, press Transfers older For Indicator Control windowNetwork window on 124 About Network Camera Setup Problem Cause and RemedyRefer to page 91 for the Update Firmware About Top View Image screen Lens View Image Setting window on About Other Troubles Confirmation of Network Camera Operation Click the language to change the display FCC and Other Information Medical Encryption WEP GlossaryAdHoc Ieee 802.11b 132 Index 133 Operating Instructions TCP/IP Wireless Router 37 Wireless window 136 137 For product service When you ship the product