Wall Mounting, Stand if necessary | Panasonic KX-HCM270 specification

Operating Instructions

Wall Mounting

1)Mount the Flexible Stand firmly to a wall or beam using the three screws (accessories). Set the Flexible Stand 240 mm (9.5 inches) away from the ceiling.

•Use appropriate screws suited for the material of the wall.

2)Attach Network Camera by screwing the threaded mount into the tripod mounting hole. A mounting hole on the rear side is also available.

3)Adjust the position of Network Camera and secure the Flexible Stand firmly.

4)Roll up the cables and Flexible Stand with the Self Bonding tape (accessories). Refer to page 96 for waterproofing the cables.

1)	2)

240 mm

(9.5 inches)

3)	4)	Caulk around Flexible
		Stand if necessary.

Waterproof the rest of the cable.

Self Bonding tape

102

Image 102

Panasonic KX-HCM270 Wall Mounting, Stand if necessary, Waterproof the rest of the cable Self Bonding tape 102

Contents

Network Camera Introduction For operation assistance Call Trademarks Network Camera MemoFor assistance, please call Important Safety Instructions Table of Contents Specifications and Troubleshooting 111 Technical GuidesIndex 133 Section Main Features Getting to Know Network Camera Authentication Multi-Client AccessUpdate Firmware Multi-Camera Screen System Requirements Authentication-System Security Feature Authentication window Self Bonding tape Connector Cover Included AccessoriesSetup CD-ROM 1 pc Rubber Cap 1 pc AC Adaptor 1 pc Flexible Stand 1 pc Sunshade 1 pc Setup CD-ROM Front View Camera Feature LocationsLens Cover Indicator Fixed Focus Lens Rear View Bottom View Network Camera Setup Installation Procedure Network Camera Configuration Type Network Camera can be installed on the LAN/IntranetType 2-Internet Connection with a Broadband Router Type 3-Internet Direct Connection with a Modem Type 4-Direct Connection with a PC How to turn on Network Camera for Installation Network Parameters Preparing the Network Parameters for Network CameraNetwork parameters memo for Network Camera Network Parameters Table Network Camera Configuration TypeDefault Type Port No How to refer the network parameters from the PC Click OK to close IP Configuration window Setting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Wireless Setup To access Network windowTo set up the wireless network parameters Connection and Signal Strength status Set Infrastructure Default or AdHocChannel Encryption Password window Encryption Key window Default Key Wireless Settings If Top Page does not appear Network Camera Access from the Internet Port Forwarding IP Masquerade feature Top Network Camera Screen and Setup Window Network Camera Flow Chart Top ExampleHttp//Global IP address of Broadband RouterPortNo Top Multi-Camera Motion JpegSingle Camera Help ActiveX Controls Single Camera Screen Click to Center Using Operation Bar Using Pan/Tilt Operation Setting Preset Positioning and Home Positioning Deleting the preset buttons Click Delete Non Transfer mode Alarm/Timer mode Viewing Buffered Image Screen Primary ViewerClicking Start Capture Secondary Multi-Camera Screen Setup Setup Name/Time AdministratorGo to Top Security External Output Indicator ControlReset to Factory Control Go to Top Network Instructions for the data fields Enter only the number Host Name When your ISP uses the Dhcp server function which If you use Network Camera on the LAN, set upCheck Dhcp Dynamic Host Configuration Protocol Or administrator for the Host name File size of the image Name Name/TimeCamera Date Auto AdjustmentTime Changed AM/PM or 24H Time Zone Security Administrator Refer to page 65 for details about authentication securityClick Security Administrator on Setup For Setup Password EnableAdministrator and General User Authentication window Retype Click Security General User on Setup Security General User Operating Instructions Top View Image Image ResolutionInstructions for the data fields Top 160 x Image Transfer Non Transfer mode Transfer in the Alarm Mode Click Alarm on Image Transfer window Alarm enable condition Active Time of Trigger Login timing Over write setting Data transfer method Setting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Image Frequency Sets the interval to send the image Login timing Over write setting Fixed Indoor Camera SetupInstructions for the data fields White Balance Fixed Having reached the selected end White Balance is also registered in preset programmingSuggested Tilt Range Click Save when finished Specifying the Pan/Tilt range Multi-Camera URL * 1 or Host Enable check boxIP Address or Camera Name Click External Output Control on Setup External Output Control Indicator Control Status Click Cancel to quit. The window returns to Setup RestartClick Restart Now Update Firmware Click Update Firmware on Setup Click Update Firmware Open Reset to Factory Default Technical Guides Network Camera Installation Outdoor Installation High performance for wireless communication Network Camera Cabling Be sure to thread the AC adaptor cord through the hook Cover the putties by rolling InchesDo not cover Ventilation hole 100 Flexible Stand Mounting Attach Network Camera to the tripod using the tripod boltNetwork Camera Mounting Tripod Mounting Wall Mounting Stand if necessaryWaterproof the rest of the cable Self Bonding tape 102 Ceiling Mounting Caulk around Flexible Stand if necessaryWaterproof the rest Cable For assistance, please call 103 Top Bottom Making holes on mortar wall Pin Function Interfacing to the External I/OExplanation of External I/O External Sensor Input Circuit Diagram Example Space, , , #, &, %, =, +, ?, , and are not available Ascii and ISO-8859-1 Character TableUnavailable character set 108 Displayable character set For assistance, please call 109 Maintenance 110 Specifications and Troubleshooting For assistance, please call 111 Network Camera Reset Procedure-Default Settings 112 Default Settings List For assistance, please call 113 114 Items Factory Default Indispensable setting Value Alarm For assistance, please call 115 Timer 116 Items Factory Default Indispensable setting Value Timer 117 Control Indicator Control 118 Specifications Network Camera Specifications DescriptionOther Specification Description Mm 3.46 inches Weight 570 1.26 lb. Only the unitMessage Transferring Method Excluding the antenna and protruding objects Troubleshooting About Network Camera SetupProblem Cause and Remedy When you use DDNS, you need to set Default Gateway Proxy server may prevent you from connecting directly toWhen Top Page does not appear, port number 80 might not be If Top Page does not appear in the above procedure, press For Indicator Control window Network window onTransfers older About Network Camera Setup Problem Cause and Remedy Refer to page 91 for the Update Firmware124 About Top View Image screen Lens View Image Setting window on About Other Troubles Confirmation of Network Camera Operation Click the language to change the display FCC and Other Information Medical Encryption WEP GlossaryAdHoc Ieee 802.11b 132 Index 133 Operating Instructions TCP/IP Wireless Router 37 Wireless window 136 137 For product service When you ship the product