Setting Example | Panasonic KX-HCM270 instruction

Operating Instructions

Setting Example

a.

b.

c.

d.

e.

f.

76

Image 76

Panasonic KX-HCM270 operating instructions Setting Example

Contents

Network Camera Introduction For operation assistance Call Network Camera Memo TrademarksFor assistance, please call Important Safety Instructions Table of Contents Technical Guides Specifications and Troubleshooting 111Index 133 Section Main Features Getting to Know Network Camera Multi-Client Access Update FirmwareAuthentication Multi-Camera Screen System Requirements Authentication-System Security Feature Authentication window Included Accessories Setup CD-ROM 1 pc Rubber Cap 1 pcSelf Bonding tape Connector Cover AC Adaptor 1 pc Flexible Stand 1 pc Sunshade 1 pc Setup CD-ROM Camera Feature Locations Lens Cover IndicatorFront View Fixed Focus Lens Rear View Bottom View Network Camera Setup Installation Procedure Network Camera can be installed on the LAN/Intranet Network Camera Configuration TypeType 2-Internet Connection with a Broadband Router Type 3-Internet Direct Connection with a Modem Type 4-Direct Connection with a PC How to turn on Network Camera for Installation Preparing the Network Parameters for Network Camera Network ParametersNetwork parameters memo for Network Camera Network Camera Configuration Type DefaultNetwork Parameters Table Type Port No How to refer the network parameters from the PC Click OK to close IP Configuration window Setting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display To access Network window Wireless SetupTo set up the wireless network parameters Set Infrastructure Default or AdHoc Connection and Signal Strength statusChannel Encryption Password window Encryption Key window Default Key Wireless Settings If Top Page does not appear Network Camera Access from the Internet Port Forwarding IP Masquerade feature Top Network Camera Screen and Setup Window Network Camera Flow Chart Example TopHttp//Global IP address of Broadband RouterPortNo Top Motion Jpeg Single CameraMulti-Camera Help ActiveX Controls Single Camera Screen Click to Center Using Operation Bar Using Pan/Tilt Operation Setting Preset Positioning and Home Positioning Deleting the preset buttons Click Delete Non Transfer mode Alarm/Timer mode Viewing Buffered Image Screen Viewer Clicking Start CapturePrimary Secondary Multi-Camera Screen Setup Setup Administrator Go to TopName/Time Security Indicator Control Reset to FactoryExternal Output Control Go to Top Network Instructions for the data fields Enter only the number If you use Network Camera on the LAN, set up Check Dhcp Dynamic Host Configuration ProtocolHost Name When your ISP uses the Dhcp server function which Or administrator for the Host name File size of the image Name/Time CameraName Date Adjustment Time Changed AM/PM or 24HAuto Time Zone Refer to page 65 for details about authentication security Security AdministratorClick Security Administrator on Setup Enable Administrator and General User Authentication windowFor Setup Password Retype Click Security General User on Setup Security General User Operating Instructions Top View Image Resolution Instructions for the data fields TopImage 160 x Image Transfer Non Transfer mode Transfer in the Alarm Mode Click Alarm on Image Transfer window Alarm enable condition Active Time of Trigger Login timing Over write setting Data transfer method Setting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Image Frequency Sets the interval to send the image Login timing Over write setting Camera Setup Instructions for the data fields White BalanceFixed Indoor Fixed White Balance is also registered in preset programming SuggestedHaving reached the selected end Tilt Range Click Save when finished Specifying the Pan/Tilt range Multi-Camera Enable check box IP Address orURL * 1 or Host Camera Name Click External Output Control on Setup External Output Control Indicator Control Status Restart Click Cancel to quit. The window returns to SetupClick Restart Now Update Firmware Click Update Firmware on Setup Click Update Firmware Open Reset to Factory Default Technical Guides Network Camera Installation Outdoor Installation High performance for wireless communication Network Camera Cabling Be sure to thread the AC adaptor cord through the hook Inches Cover the putties by rollingDo not cover Ventilation hole 100 Attach Network Camera to the tripod using the tripod bolt Network Camera MountingFlexible Stand Mounting Tripod Mounting Stand if necessary Wall MountingWaterproof the rest of the cable Self Bonding tape 102 Caulk around Flexible Stand if necessary Ceiling MountingWaterproof the rest Cable For assistance, please call 103 Top Bottom Making holes on mortar wall Interfacing to the External I/O Explanation of External I/OPin Function External Sensor Input Circuit Diagram Example Ascii and ISO-8859-1 Character Table Unavailable character setSpace, , , #, &, %, =, +, ?, , and are not available 108 Displayable character set For assistance, please call 109 Maintenance 110 Specifications and Troubleshooting For assistance, please call 111 Network Camera Reset Procedure-Default Settings 112 Default Settings List For assistance, please call 113 114 Items Factory Default Indispensable setting Value Alarm For assistance, please call 115 Timer 116 Items Factory Default Indispensable setting Value Timer 117 Control Indicator Control 118 Network Camera Specifications Description SpecificationsOther Specification Description Weight 570 1.26 lb. Only the unit Message Transferring MethodMm 3.46 inches Excluding the antenna and protruding objects About Network Camera Setup TroubleshootingProblem Cause and Remedy Proxy server may prevent you from connecting directly to When Top Page does not appear, port number 80 might not beWhen you use DDNS, you need to set Default Gateway If Top Page does not appear in the above procedure, press Network window on For Indicator Control windowTransfers older Refer to page 91 for the Update Firmware About Network Camera Setup Problem Cause and Remedy124 About Top View Image screen Lens View Image Setting window on About Other Troubles Confirmation of Network Camera Operation Click the language to change the display FCC and Other Information Medical Glossary AdHocEncryption WEP Ieee 802.11b 132 Index 133 Operating Instructions TCP/IP Wireless Router 37 Wireless window 136 137 For product service When you ship the product