Panasonic KX-HCM270 manual

Operating Instructions

2.3How to turn on Network Camera for Installation

Network Camera is powered up when connecting AC plug to the power outlet.

1.Connect Category 5 straight/cross cable to the Ethernet port of Network Camera to the hub or PC.

•Connect Ethernet cable first to make Network Camera recognize the wired communication.

2.Connect the DC plug of the AC adaptor to the DC IN jack and the AC plug of the AC adaptor to the power outlet to turn on Network Camera. Indicator blinks and the Pan/Tilt moves to the center position.

AC adaptor

Power

Outlet

DC IN

jack

Ethernet port

2.
1.
DC Plug	To Network
Category 5 straight/cross cable

Notes

•AC adaptor is used as the main disconnect device, so ensure that the power outlet is located/installed near the equipment and is easily accessible.

•Use only the specified Panasonic AC adaptor PSLP1233 (Order No. PSLP1233Z).

•When you set up Network Camera in [Type 3], connect it temporarily in [Type 1], [Type 2] or [Type 4].

•When Indicator is orange, confirm that the Ethernet cable is properly connected, or PC, Ethernet hub or broadband router is properly working.

20

Image 20

Panasonic KX-HCM270 operating instructions How to turn on Network Camera for Installation

Contents

Network Camera Introduction For operation assistance Call For assistance, please call TrademarksNetwork Camera Memo Important Safety Instructions Table of Contents Index 133 Specifications and Troubleshooting 111Technical Guides Section Main Features Getting to Know Network Camera Multi-Client Access Update FirmwareAuthentication Multi-Camera Screen System Requirements Authentication-System Security Feature Authentication window Included Accessories Setup CD-ROM 1 pc Rubber Cap 1 pcSelf Bonding tape Connector Cover AC Adaptor 1 pc Flexible Stand 1 pc Sunshade 1 pc Setup CD-ROM Camera Feature Locations Lens Cover IndicatorFront View Fixed Focus Lens Rear View Bottom View Network Camera Setup Installation Procedure Type 2-Internet Connection with a Broadband Router Network Camera Configuration TypeNetwork Camera can be installed on the LAN/Intranet Type 3-Internet Direct Connection with a Modem Type 4-Direct Connection with a PC How to turn on Network Camera for Installation Network parameters memo for Network Camera Network ParametersPreparing the Network Parameters for Network Camera Network Camera Configuration Type DefaultNetwork Parameters Table Type Port No How to refer the network parameters from the PC Click OK to close IP Configuration window Setting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display To set up the wireless network parameters Wireless SetupTo access Network window Channel Connection and Signal Strength statusSet Infrastructure Default or AdHoc Encryption Password window Encryption Key window Default Key Wireless Settings If Top Page does not appear Network Camera Access from the Internet Port Forwarding IP Masquerade feature Top Network Camera Screen and Setup Window Network Camera Flow Chart Http//Global IP address of Broadband RouterPortNo Top TopExample Motion Jpeg Single CameraMulti-Camera Help ActiveX Controls Single Camera Screen Click to Center Using Operation Bar Using Pan/Tilt Operation Setting Preset Positioning and Home Positioning Deleting the preset buttons Click Delete Non Transfer mode Alarm/Timer mode Viewing Buffered Image Screen Viewer Clicking Start CapturePrimary Secondary Multi-Camera Screen Setup Setup Administrator Go to TopName/Time Security Indicator Control Reset to FactoryExternal Output Control Go to Top Network Instructions for the data fields Enter only the number If you use Network Camera on the LAN, set up Check Dhcp Dynamic Host Configuration ProtocolHost Name When your ISP uses the Dhcp server function which Or administrator for the Host name File size of the image Name/Time CameraName Date Adjustment Time Changed AM/PM or 24HAuto Time Zone Click Security Administrator on Setup Security AdministratorRefer to page 65 for details about authentication security Enable Administrator and General User Authentication windowFor Setup Password Retype Click Security General User on Setup Security General User Operating Instructions Top View Image Resolution Instructions for the data fields TopImage 160 x Image Transfer Non Transfer mode Transfer in the Alarm Mode Click Alarm on Image Transfer window Alarm enable condition Active Time of Trigger Login timing Over write setting Data transfer method Setting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Image Frequency Sets the interval to send the image Login timing Over write setting Camera Setup Instructions for the data fields White BalanceFixed Indoor Fixed White Balance is also registered in preset programming SuggestedHaving reached the selected end Tilt Range Click Save when finished Specifying the Pan/Tilt range Multi-Camera Enable check box IP Address orURL * 1 or Host Camera Name Click External Output Control on Setup External Output Control Indicator Control Status Click Restart Now Click Cancel to quit. The window returns to SetupRestart Update Firmware Click Update Firmware on Setup Click Update Firmware Open Reset to Factory Default Technical Guides Network Camera Installation Outdoor Installation High performance for wireless communication Network Camera Cabling Be sure to thread the AC adaptor cord through the hook Do not cover Ventilation hole 100 Cover the putties by rollingInches Attach Network Camera to the tripod using the tripod bolt Network Camera MountingFlexible Stand Mounting Tripod Mounting Waterproof the rest of the cable Self Bonding tape 102 Wall MountingStand if necessary Waterproof the rest Cable For assistance, please call 103 Ceiling MountingCaulk around Flexible Stand if necessary Top Bottom Making holes on mortar wall Interfacing to the External I/O Explanation of External I/OPin Function External Sensor Input Circuit Diagram Example Ascii and ISO-8859-1 Character Table Unavailable character setSpace, , , #, &, %, =, +, ?, , and are not available 108 Displayable character set For assistance, please call 109 Maintenance 110 Specifications and Troubleshooting For assistance, please call 111 Network Camera Reset Procedure-Default Settings 112 Default Settings List For assistance, please call 113 114 Items Factory Default Indispensable setting Value Alarm For assistance, please call 115 Timer 116 Items Factory Default Indispensable setting Value Timer 117 Control Indicator Control 118 Other Specification Description SpecificationsNetwork Camera Specifications Description Weight 570 1.26 lb. Only the unit Message Transferring MethodMm 3.46 inches Excluding the antenna and protruding objects Problem Cause and Remedy TroubleshootingAbout Network Camera Setup Proxy server may prevent you from connecting directly to When Top Page does not appear, port number 80 might not beWhen you use DDNS, you need to set Default Gateway If Top Page does not appear in the above procedure, press Transfers older For Indicator Control windowNetwork window on 124 About Network Camera Setup Problem Cause and RemedyRefer to page 91 for the Update Firmware About Top View Image screen Lens View Image Setting window on About Other Troubles Confirmation of Network Camera Operation Click the language to change the display FCC and Other Information Medical Glossary AdHocEncryption WEP Ieee 802.11b 132 Index 133 Operating Instructions TCP/IP Wireless Router 37 Wireless window 136 137 For product service When you ship the product